User manual BEKO HIZE 64101 DIMENSIONS

[. . . ] 38 Switching a cooking zone off automatically. 49 Safety instructions for installation . 70 3 Guide to the appliance KM 5731 abcd Cooking zones e Cooking zone controls and displays (see "Cooking zone controls and displays") f Timer control and display (see "Timer control and display") g Safety lock indicator lamp h Safety lock sensor switch i Hob ON/OFF sensor switch 4 Guide to the appliance KM 5732 / KM 5736 / KM 5737 abcd Cooking zones e Cooking zone controls and displays (see "Cooking zone controls and displays") f Timer control and display (see "Timer control and display") g Safety lock indicator lamp h Safety lock sensor switch i Hob ON/OFF sensor switch 5 Guide to the appliance KM 5733 abc Cooking zones e Cooking zone controls and displays (see "Cooking zone controls and displays") f Timer control and display (see "Timer control and display") g Safety lock indicator lamp h Safety lock sensor switch i Hob ON/OFF sensor switch 6 Guide to the appliance KM 5752 / KM 5757 abcd Cooking zones e Cooking zone controls and displays (see "Cooking zone controls and displays") f Timer control and display (see "Timer control and display") g Safety lock indicator lamp h Safety lock sensor switch i Hob ON/OFF sensor switch 7 Guide to the appliance KM 5753 abcd Cooking zones e Cooking zone controls and displays (see "Cooking zone controls and displays") f Timer control and display (see "Timer control and display") g Safety lock indicator lamp h Safety lock sensor switch i Hob ON/OFF sensor switch 8 Guide to the appliance HIZE 64101 abcd Cooking zones e Cooking zone controls and displays (see "Cooking zone controls and displays") f Timer control and display (see "Timer control and display") g Safety lock indicator lamp h Safety lock sensor switch i Hob ON/OFF sensor switch 9 Guide to the appliance KM 5775 abcd Cooking zones e Cooking zone controls and displays (see "Cooking zone controls and displays") f Timer control and display (see "Timer control and display") g Safety lock indicator lamp h Safety lock sensor switch i Hob ON/OFF sensor switch 10 Guide to the appliance Cooking zone sensors and displays j Displays: 0 = 1 to 9 = # = ß = F A P0 etc. = = = = Cooking zone ready for use Power settings (for switched on hob) Residual heat No pan on cooking zone or pan unsuitable (see "Induction") Fault (see "Safety switch-off") Auto heat-up when the power setting range has been extended Programme (see "Programming") Status (see "Programming") k Indicator lamp for Auto heat-up or extended power setting (see "Programming"), e. g. [. . . ] ­ the power level on the other linked cooking zone will sometimes decrease. Proceed as follows: ^ Touch the B sensor for the relevant cooking zone. Power setting 9 will show in the cooking zone display, and the indicator lamp for the booster will also light up. After 10 minutes, the zone will automatically revert to power setting 9. To switch off the booster before this, touch either the B sensor or the sensor for the appropriate cooking zone. If a power setting is selected before the booster function is switched on, the zone will revert to this pre-selected power setting when the booster is switched off, or automatically at the end of the booster time. 32 Use Switching off and residual heat indicators To switch off a cooking zone: ^ Touch the - and + sensors for the zone you want to switch off at the same time. A 0 will light up in the display for that zone for a few seconds. If the cooking zone is still hot, residual heat will then be indicated in the display. The lines of the residual heat indicator go out one after another as the cooking zones cool down. The last horizontal line only goes out when the cooking zone is safe to touch. The residual heat indicators also react to hot dishes and plates being placed on a cooking zone that is not switched on. Do not touch any zone or place any heat sensitive items on a zone where the residual heat indicator is lit up. To deactivate Stop and Go: ^ Touch the safety lock sensor $ until the indicator lamp goes out. The cooking zones will now run at the level that was previously set. 35 Safety features Safety switch-off Safety switch-off with an over-long cooking time Your hob is fitted with a safety switch-off feature in case you forget to switch it off yourself. If one of the cooking zones is heated for an unusually long period of time (see chart), and the power settings are not altered, the hob will switch itself off automatically and the appropriate residual heat indicator will appear. Power setting* Maximum operating time in hours 10 5 5 4 3 2 2 2 1 Safety switch-off if the sensors are covered Your hob will switch off automatically if one or several of the sensors remain covered for longer than 10 seconds, for example, by finger contact, food boiling over or by an object such as an oven glove or tea towel. An audible tone will sound every 30 seconds (for a maximum of ten minutes) and an F will flash in the display for the sensor which is covered. 1 / 1. 9 ^ Clean the control area or remove the obstruction. This will turn off the tone and the F will go out. ^ Switch the hob back on again with the ON/OFF sensor s. The cooking zones can now be used again as normal. * The power settings with a dot after the number are only available if the power setting range has been extended (see "Programming - P6. "). ^ To use the cooking zones again, switch the hob back on in the usual way. 36 Safety features Overheating protection All of the induction coils and the cooling element for the electronics are fitted with an overheating protection mechanism. To prevent the induction coils and cooling element from overheating, the overheating protection mechanism works on the affected cooking zone or on the entire hob in the following ways: ­ If the booster function is being used, this will be switched off. [. . . ] ^ Feed the hob connection cable down through the cut-out. ^ Centre the hob f in the cut-out. 6 1 0 50 7 g 02 f ^ Connect the hob to the mains. ^ Seal the remaining gap g with a silicone sealant that is heat-resistant to at least 160 °C. e 13 51 52 e Worktop f Hob g Gap Corner radius of the worktop ß R4 As the ceramic glass and the worktop cut-out have a certain dimensional tolerance, gap g can vary (min. 2 mm). 66 Installation Solid wood and tiled worktops ^ Make the worktop cut-out as shown in drawings. [. . . ]