User manual BELKIN F1D066

[. . . ] All of which, come standard with the Belkin OmniView. Check the end of this booklet for more information on OmniView accessories!Features: · Allows a user to control over as many as 64 computers from one keyboard, mouse and monitor · Supports both PS/2 and serial mice simultaneously · Supports both PS/2- and AT-style keyboards · Supports VGA, SVGA and Multisync monitors · Uses standard cables · Pushbutton or keyboard hot-key sequence switching · Auto scan mode and quick last/next switching modes for even more convenience · Audible feedback when switching · Recalls CAPS LOCK, NUM LOCK, and SCROLL LOCK keys' status for each computer automatically · Front-panel status LEDs · Works with other OmniView accessories (MAC Adapter, FootSwitch and RackMount kit) · No software required · One year product warranty Package Contents: 4-Port OmniView PS/2 9VDC, 600mA power supply This manual F1D066 F1D065-PWR P72115 Technical Specs: Console Connectors Keyboard: Mouse: Monitor: Computer Port Connectors Keyboard: Mouse: Monitor: Power Supply Dimensions Width: Height (with feet): Depth: Weight Operating Temperature Storage Temperature Humidity DIN-5 female for AT-style keyboard Mini-DIN-6 female for PS/2 style-keyboard DB-9 male for serial mouse Mini-DIN-6 female for PS/2 mouse HD-DB-15 female for VGA monitor DIN-5 female for AT-style keyboard Mini-DIN-6 female for PS/2 style-keyboard DB-9 female for serial mouse Mini-DIN-6 female for PS/2 mouse HD-DB-15 male for VGA monitor 9VDC, 600mA 10 inches (25. 4 cm) 3. 25 inches (8. 26 cm) 7. 13 inches (18. 11 cm) 6. 82 lbs. C 0-80% RH, non-condensing Hardware Installation: 1. [. . . ] Then, select the port on the cascaded OmniView where the desired computer is connected. · Entering the hot-key sequence allows direct port access from the keyboard, even through cascaded OmniViews. The procedure is very simple, and easy to remember: 1. Press <ALT>+<CTRL>+<SHIFT> all at the same time, then release. Press the port number of the computer you wish to control. If you have cascaded OmniViews, you will have to press two (or three) numbers, x y z, where x is the port on the top level OmniView, y is the port on the second level OmniView, and z is the port on the third level OmniView. Press the correct key (or keys in succession), then release. You should hear a beep to confirm the OmniView has switched to the desired port. For example, pressing <ALT>+<CTRL>+<SHIFT> 1 2 3 <ENTER> selects Port 1 on the top level OmniView, Port 2 on the second level OmniView, and Port 3 on the third level OmniView. The OmniView filters out the hot-key sequences, preventing unwanted characters from appearing in the computer's applications. Scan Mode The OmniView can be set for automatic scan mode. In scan mode, the OmniView switches from one computer to the next in regular time intervals set by the DIP switches. When the OmniView is in scan mode, there is no keyboard control passed to the displayed computers. This is necessary because switching is handled by the OmniView, not the operator. Note: Scan mode will continue indefinitely, until the <SPACE> bar is pressed and scan mode is terminated. Also, the OmniView will only scan to ports that have computers enabled on it. · To invoke scan mode, the following hot key sequence must be entered: <ALT>+<CTRL>+<SHIFT> 0 <ENTER> You will then hear a beep to confirm scan mode is taking place, and this can be verified visually by the flashing lights on the currently selected computer port. Setting the scan time on each port is done through the DIP switches found on the back of the OmniView: DIP Switch Number Scan Time 1 2 3 4 (seconds) ON ON OFF ON 3 OFF ON OFF ON 10 ON OFF OFF ON 20 OFF OFF OFF ON 40 Quick Last/Next Switching mode Quick Last/Next switching mode is similar to scan mode, except the operator has control over the switching. In this mode, the operator can press either one of the shift keys to switch to the adjacent computer previous or after the currently selected port. There is also no keyboard control during this mode, but the mouse is still completely operable. Note: Quick Last/Next switching mode will continue indefinitely, until the <SPACE> bar is pressed and is terminated. · To invoke quick Last/Next switching mode, the following hot key sequence must be entered: <ALT>+<CTRL>+<SHIFT> 9 <ENTER> You will then hear a beep to confirm quick Last/Next switching mode is taking place, and this can be verified visually by the slow blinking light on the currently selected computer port. · · To select the next adjacent computer, press the RIGHT side <SHIFT> key. [. . . ] BELKIN COMPONENTS PRODUCT WARRANTY Belkin Components warrants this product against defects in materials and workmanship for one year. If a defect is discovered, Belkin will, at its option, repair or replace the product at no charge provided it is returned during the warranty period, with transportation charges prepaid, to the authorized Belkin dealer from whom you purchased the product. This warranty does not apply if the product has been damaged by accident, abuse, misuse, or misapplication; if the product has been modified without the written permission of Belkin; or if any Belkin serial number has been removed or defaced. THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. [. . . ]