User manual BELKIN F1D094

[. . . ] We recommend purchasing PS/2 Cable Kits, as it contains all the cables you need to connect one computer to the OmniCubeTM. Includes: · Two F2N036-06 · One F2N025-06-T (see below for descriptions of each) Individual Cables: · PS/2 cable for keyboard and mouse ports Mini-DIN6 male/male Part #F2N036-XX · Standard VGA cable for monitor port HDDB15 male/female with thumbscrews Part #F2N025-XX-T Mini-DIN6 HDDB15 Other Cables and Adapters: · High-resolution/high-refresh rate VGA cable for monitor port HDDB15 male/female with thumbscrews Part #A3H981-XX · AT to PS/2 keyboard adapter - for use with an AT-style keyboard at the console of the OmniCubeTM DIN5 female/ Mini-DIN6 male DIN5 Female Part #F2N017 · PS/2 to AT keyboard adapter - for use with a computer having an AT-style key board port Mini-DIN6 female/ DIN5 male Mini DIN6 Female Part #F2N018 NOTE: The "XX" in the part number represents the length in feet. 6 Mini DIN6 Male DIN5 Male Hardware Installation WARNING: Follow these directions closely and in the proper order. Failure to do so may result in mouse and/or keyboard errors. Before attempting to connecting anything to the OmniCubeTM or the computers, make sure everything is powered off. Plugging and unplugging cables may cause irreversible damage to your computers and the OmniCubeTM. [. . . ] If this is okay, press the SELECT button and check the functionality of the second computer. If you find any errors, double check all the cable connections. 10. You can now power up both computers simultaneously. The first 9 Usage Selecting which computer to operate can be done either by pressing the SELECT button, or through keyboard hot-key commands. You will notice that after the OmniCubeTM switches to another computer, the mouse will be inoperative for about 1-2 seconds. This is normal operation and ensures that proper mouse synchronization is established. 4-Port OmniCubeTM 12 CONSOLE 34 Select Pressing the SELECT button cycles you through ports 1 - 4. F1D094 Keyboard Hot-Key commands: To send commands to the OmniCubeTM, the SCROLL LOCK key must be pressed twice within 2 seconds. Below are the different commands: Scroll Lock Scroll Lock 1 : Switch to Port 1 : Switch to Port 3 : Switch to previous port Scroll Lock Scroll Lock 2 : Switch to Port 2 : Switch to Port 4 : Switch to next port Scroll Lock Scroll Lock 3 Scroll Lock Scroll Lock 4 Scroll Lock Scroll Lock Scroll Lock Scroll Lock Scroll Lock Scroll Lock 0 : Enables AutoScan mode. In AutoScan mode, the OmniCubeTM remains on one port for 10 seconds before switching to the next. There is no mouse or keyboard control in this mode. Otherwise, if the user is moving the mouse or using the keyboard when the OmniCubeTM switches to the next port, data flow is interrupted and will cause erratic mouse movement and/or the wrong characters to show up when using the keyboard. To get out of AutoScan mode, hit the SPACEBAR. 10 Troubleshooting Video: Q: I am getting ghosting, shadowing or fuzzy images on my monitor. A: · Check the cables and make sure they are inserted properly. · Your resolution and/or refresh rate is extremely high, or your cable is too long. Replace your VGA cables with coaxial, double-shielded cables such as Belkin Part #A3H981-XX. · Check to make sure that the power adapter is plugged in and is working properly. · Lower your refresh rate and/or screen resolution settings. Keyboard: Q: The keyboard is not detected, or a keyboard error is reported during boot-up. A: · Check the cables and make sure they are inserted properly. Q: The computers boot up fine, but the keyboard does not work. A: · Make sure it is plugged in properly. · Make sure the keyboard works when directly plugged into the computer. · Check to make sure that the power adapter is plugged in and is working properly. It must be 9VDC, 500mA minimum. Mouse: Q: The mouse is not detected during boot-up. A: · Check the cables and make sure they are inserted properly. · Check your computer/motherboard documentation and make sure that the PS/2 mouse port (or IRQ) is enabled. 11 Troubleshooting (continued) Mouse: (continued) Q: The computers boot up fine, but the mouse does not work. [. . . ] Before booting up the PCs, the OmniCubeTM must be powered with its power supply. But before attaching the OmniCubeTM power supply, the keyboard and mouse MUST be connected first. 12 Information FCC/CE Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if no installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ]