User manual BELKIN F1DB104P2EA

[. . . ] Push buttons, conveniently located on the front panel of the E Series KVM Switch, allow for simple, manual port selection. The E Series KVM Switch is compatible with CPUs running on, but not limited to, the following OS platforms: · An optional 9V 600mA power supply is available (Belkin Part number F1D084PWR-EUR (With Schuko Plug) and F1D084-PWR-EUR (With UK Plug)). This is only required in rare cases where the power output from the connected computer is not adequate to power the KVM Switch. : Enclosure: Power: F1DB102P2, F1DB104P2 High-impact plastic By PS/2 computer keyboard port; optional 9V DC, 600mA power adapter, center-pin-positive polarity 2 and 4 respectively for 2- and 4-port models CRT and LCD (with VGA support) Up to 1920x1440 @ 75Hz PS/2 (miniDIN6) PS/2 (miniDIN6) VGA (HDDB15 female) HDDB15 female 32° to 104° F (0~40° C) -4° to 140° F (20~60° C) 0-80% RH, non-condensing 2 years (F1DB102P2) 5. [. . . ] To stop AutoScan, press any button on the front panel or any key on the keyboard. note: There is no mouse or keyboard control in AutoScan mode. This is necessary to prevent data and synchronization errors. If the user is using the mouse or keyboard when the E Series KVM Switch is switching between ports, data flow may become interrupted and could result in erratic mouse movement and/or wrong-character input when using the keyboard. Below is a complete list of hot-key commands that can be used for your E Series KVM Switch: Note: Each command needs to be preceded by "Scroll Lock", "Scroll Lock". Note: You will have approximately three seconds to complete each hot-key sequence. A: The E Series KVM Switch will support any operating system that runs on a PS/2 platform only. Q: How far can the computer be from the KVM Switch?A: The KVM Switch can be placed up to 25 feet away from your PS/2 computer. Q: Do I have to install any software to use the KVM Switch?A: No, the KVM Switch does not require any drivers or software to be installed in your computers. Simply connect all your computers to the Belkin KVM Cable Kits, and then attach one keyboard, monitor, and mouse to the console port, and it is ready for use. q: Does the KVM Switch require an AC adapter?A: No, the KVM Switch can be used in the majority of cases without an external power adapter. q: Can I use the E Series KVM Switch to switch video signals only?A: No, the KVM Switch must be connected to both the video and keyboard/ mouse ports on your computers. The KVM Switch detects the power from the PS/2 ports on your computers in order to function. A: Yes, the KVM Switch works with Red Hat and other Linux distributions configured for PS/2 support. My computer does not boot up when connected to the KVM Switch, but works fine when I connect the keyboard, video, and mouse directly to the computer. ⷠMake sure that the keyboard and mouse cables are connected tightly between the KVM Switch and the computer. Check that the monitor you are using supports the resolution and refreshrate setting on your computer. ⷠLower the video resolution of your monitor. [. . . ] Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. cE Declaration of Conformity We , Belkin International , Inc. , declare under our sole responsibility that the products F1DB102P2, F1DB104P2, to which this declaration relates, are in conformity with Emissions Standard EN55022 and with Immunity Standard EN55024, LVP EN61000-3-2, and EN61000-3-3. ("Belkin") warrants to the original purchaser of this Belkin product that the product shall be free of defects in design, assembly, material, or workmanship. [. . . ]