User manual BELKIN F1DJ102P

[. . . ] Belkin Corporation 501 West Walnut Street Compton · CA · 90220 · USA Tel: 310. 898. 1100 Fax: 310. 898. 1111 2-Port KVM Switch Belkin Components, Ltd. Express Business Park · Shipton Way · Rushden NN10 6GL · United Kingdom Tel: +44 (0) 1933 35 2000 Fax: +44 (0) 1933 31 2000 Control two computers using one video monitor and a PS/2 keyboard and mouse Belkin Components B. V. Starparc Building · Boeing Avenue 333 1119 PH Schiphol-Rijk · The Netherlands Tel: +31 (0) 20 654 7300 Fax: +31 (0) 20 654 7349 Belkin, Ltd. 7 Bowen Crescent · West Gosford NSW 2250 · Australia Tel: +61 (0) 2 4372 8600 Fax: +61 (0) 2 4372 8603 Belkin Tech Support US: Europe: Australia: 310. 898. 1100 ext. 2263 00 800 223 55 460 1800 666 040 P74225 © 2003 Belkin Corporation. All trade names are registered trademarks of respective manufacturers listed. User Manual F1DJ102P-B TABLE OF CONTENTS Introduction Package Contents . Equipment Requirements Operating Systems . [. . . ] Note that it will take 1-2 seconds for the video to display after switching. This is due to the refresh of the video signal. A re-synchronization of the mouse and keyboard signal also takes place. This is normal operation and ensures that proper synchronization is established. You can conveniently change ports on the Switch through a keyboard command sequence using the "SCROLL LOCK" key and up and down arrow keys. To send commands to the Switch, press the "SCROLL LOCK" key twice within two seconds. Then you can press the up or down arrow keys to switch between ports. USING YOUR SWITCH You can switch directly to any port by entering the Switch port number you wish to use. For example, if you press "SCROLL LOCK", "SCROLL LOCK", "2", the computer on port 2 will be selected. + AutoScan Mode + Switch to Port 2--(02) In AutoScan mode, the Switch remains on one port for eight seconds before switching to the next. To enable AutoScan mode, press "SCROLL LOCK", "SCROLL LOCK", "S". Note: There is no mouse or keyboard control in this mode by design, in order to prevent errors. If it were enabled, the user could move the mouse or use the keyboard while the KVM Switch is switching to the next port. This could interrupt communication between the computer and Switch that might cause erratic mouse movement, or result in errant display of characters when using the keyboard. To disable AutoScan mode, press the space bar. Switch to next active port, up arrow 14 Switch to previous active port, down arrow 15 FAQs Q: What operating system does the Switch support?A: The Switch will support any operating system that runs on a PS/2 platform. It will also work with Sun and Mac operating systems using the appropriate adapters (Belkin OmniView Sun Adapter F1D082, OmniView Mac Adapter F1D080). Operating systems include, but are not limited to, DOS, Windows 3. x, 95, 98, 2000, Me, NT, XP, Linux, and Novell NetWare 4. x/5. x. Q: Does the Switch function with the Microsoft IntelliMouse?A: Yes, the Switch will function with Microsoft, Logitech, Kensington, as well as with all Belkin mice. The Switch will support only two mouse buttons. Please contact Belkin Technical Support for any compatibility questions you may have. Q: How does the Switch allow the user to toggle between ports?A: The Switch supports two methods of port selection. [. . . ] · Check the cables and make sure that they are inserted properly. The computer boots up fine, but the mouse does not work. · Make sure it is plugged-in properly. · Make sure the mouse works when directly plugged into the computer. [. . . ]