User manual BELKIN F1DP116G

[. . . ] OmniView® SMB KVM-over-IP Switch Belkin Tech Support US: 800-223-5546 ext. 2263 Europe: 00 800 223 55 460 Australia: 1800 235 546 New Zealand: 0800 235 546 Singapore: 800 616 1790 Belkin Corporation 501 West Walnut Street Los Angeles, CA 90220, USA 310-898-1100 310-898-1111 fax Belkin Ltd. Express Business Park, Shipton Way Rushden, NN10 6GL, United Kingdom +44 (0) 1933 35 2000 +44 (0) 1933 31 2000 fax Belkin Ltd. 7 Bowen Crescent, West Gosford NSW 2250, Australia +61 (0) 2 4372 8600 +61 (0) 2 4372 8603 fax Belkin B. V. [. . . ] To minimize or maximize the toolbar, click . Disconnecting the Remote Session To disconnect the session, click you disconnect. You may close the browser after 45 Using the Switch from a Remote Console Mouse Configuration and Settings Mouse-Pointer Alignment When working remotely at the client computer, two mouse pointers will appear: one for the client computer and one for the target server. The client computer's mouse pointer will appear on top of the target server's. The mouse pointers should be synchronized (aligned). If they are not synchronized, follow the instructions below. To align mouse pointers: 1. 2. In the quick-access toolbar, click Select "Align" or press "Ctrl+M". . Mouse-Pointer Calibration A target server may have a different mouse-pointer speed than the client computer. Calibration automatically discovers the mouse speed of the target server and aligns the two pointers. When you calibrate pointers, the Switch saves the alignment, so calibration is only needed once per target server. To calibrate mouse pointers (for servers running on Windows NT or 2000): 1. 2. In the quick-access toolbar, click Select "Calibrate". . Note: If the video-noise level is above zero, calibration may not work properly. Go to "Video Adjustment" and try to eliminate the noise by pressing "Audio Video Adjust", or by adjusting the bars in "Manual Video Adjust", then perform the mouse calibration again. 46 Using the Switch from a Remote Console Manual Settings You must manually synchronize the mouse pointers if: · the mouse setting on the target server was ever changed, or · the operating system on the target server is Windows XP, Windows 2003 Server, Linux, Novell®, SCO UNIX, or Sun SolarisTM. 1 2 3 4 section To manually synchronize mouse pointers: 1. 2. In the quick-access toolbar, click . The Mouse-Settings box will appear (see Fig. 13 Mouse-Settings Box 3. Select the target servers operating system and click "OK". Instructions and sliders will appear. 47 Using the Switch from a Remote Console 4. Follow the instructions and set any relevant sliders to the same values as set in the target servers mouse properties. Examples: For servers running on Windows XP, go to the Mouse settings in the Control Panel and uncheck "Enhance pointer precision" (see Fig. 14 Mouse-Pointer Options (Windows XP) For servers running on Windows NT, if mouse properties were ever changed--even if they were returned to their original state--uncheck "Default". 5. Click "OK". The mouse pointers should now be synchronized. USB Option In the Mouse Settings screen, you will need to select the USB option if: · a USB Server Interface Module is connected to the target server, or · the server's operating system is Linux, Sun Solaris, or Novell. If not set correctly, the mouse will frequently lose the synchronization. Some uncommon operating systems may require this USB setting to be on for proper mouse synchronization. Use this option if you are sure of the custom acceleration algorithm you are using, or if you have been informed to do so by Belkin Technical Support. 48 Using the Switch from a Remote Console Advanced-Mouse Emulation In the Advanced-Mouse settings, you can set the type of mouse you would like the Switch to emulate. [. . . ] Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 1 2 3 4 5 6 7 8 9 section CE Declaration of Conformity We, Belkin Corporation, declare under our sole responsibility that the products F1DP108G, and F1DP116G, to which this declaration relates, are in conformity with Emissions Standard EN55022 and with Immunity Standard EN55024, LVP EN61000-3-2, and EN61000-3-3. ICES This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada. Belkin Corporation Limited 3-Year Product Warranty What this warranty covers. Belkin Corporation warrants to the original purchaser of this Belkin product that the product shall be free of defects in design, assembly, material, or workmanship. [. . . ]