User manual BELKIN F1DP1XXG

[. . . ] OmniView® SMB KVM-over-IP Switch EN FR DE NL ES IT User Manual F1DP108Gea F1DP116Gea Table of Contents 1. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If they are not synchronized, follow the instructions below. To align mouse pointers: 1. 2. In the quick-access toolbar, click Select "Align" or press "Ctrl+M". . Mouse-Pointer Calibration A target server may have a different mouse-pointer speed than the client computer. Calibration automatically discovers the mouse speed of the target server and aligns the two pointers. When you calibrate pointers, the Switch saves the alignment, so calibration is only needed once per target server. To calibrate mouse pointers (for servers running on Windows NT or 2000): 1. 2. In the quick-access toolbar, click Select "Calibrate". . Note: If the video-noise level is above zero, calibration may not work properly. Go to "Video Adjustment" and try to eliminate the noise by pressing "Audio Video Adjust", or by adjusting the bars in "Manual Video Adjust", then perform the mouse calibration again. 46 Using the Switch from a Remote Console Manual Settings You must manually synchronize the mouse pointers if: · the mouse setting on the target server was ever changed, or · the operating system on the target server is Windows XP, Windows 2003 Server, Linux, Novell®, SCO UNIX, or Sun SolarisTM. 1 2 3 4 section To manually synchronize mouse pointers: 1. 2. In the quick-access toolbar, click . The Mouse-Settings box will appear (see Fig. 13 Mouse-Settings Box 3. Select the target server's operating system and click "OK". Instructions and sliders will appear. 47 Using the Switch from a Remote Console 4. Follow the instructions and set any relevant sliders to the same values as set in the target server's mouse properties. Examples: For servers running on Windows XP, go to the Mouse settings in the Control Panel and uncheck "Enhance pointer precision" (see Fig. 14 Mouse-Pointer Options (Windows XP) For servers running on Windows NT, if mouse properties were ever changed--even if they were returned to their original state--uncheck "Default". 5. Click "OK". The mouse pointers should now be synchronized. USB Option In the Mouse Settings screen, you will need to select the USB option if: · a USB Server Interface Module is connected to the target server, or · the server's operating system is Linux, Sun Solaris, or Novell. If not set correctly, the mouse will frequently lose the synchronization. Some uncommon operating systems may require this USB setting to be on for proper mouse synchronization. Use this option if you are sure of the custom acceleration algorithm you are using, or if you have been informed to do so by Belkin Technical Support. 48 Using the Switch from a Remote Console Advanced-Mouse Emulation In the Advanced-Mouse settings, you can set the type of mouse you would like the Switch to emulate. Note: Belkin recommends that you NOT change the advanced settings unless there is erratic mouse behavior (i. e. , if the mouse is making random clicks and jumping arbitrarily around the screen). 1 2 3 4 section To change the mouse-emulation settings: 1. Click . The Mouse-Emulation box will appear (see Fig. 3. Select the type of mouse physically connected to the local console port on the Switch. In the Max Rate box, choose the maximum mouse-report rate. [. . . ] All above warranties are null and void if the Belkin product is not provided to Belkin Corporation for inspection upon Belkin's request at the sole expense of the purchaser, or if Belkin Corporation determines that the Belkin product has been improperly installed, altered in any way, or tampered with. The Belkin Product Warranty does not protect against acts of God (other than lightning) such as flood, earthquake, war, vandalism, theft, normal-use wear and tear, erosion, depletion, obsolescence, abuse, damage due to low voltage disturbances (i. e. brownouts or sags), non-authorized program, or system equipment modification or alteration. 10 77 Information How to get service. To get service for your Belkin product you must take the following steps: 1. [. . . ]