User manual BELKIN F5D7000CE2

[. . . ] IMMUNITY TEST REPORT REPORT NO. : MODEL NO. : RECEIVED: TESTED: RM920221R04A F5D7000 Feb. 7, 2003 APPLICANT: Belkin Corporation 501 WEST WALNUT STREET COMPTON, ADDRESS: CA 90220 ISSUED BY: Advance Data Technology Corporation LAB LOCATION: No. 47 14th Ling, Chia Pau Tsuen, Linkou Hsiang, Taipei, Taiwan, R. O. C. This test report consists of 29 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. [. . . ] Emission Level = Correction Factor + Reading Value. Report No. : RM920221R04A Reference No. : RM920221R04 12 Issued: Mar. 14, 2003 5 IMMUNITY TEST 5. 1 GENERAL DESCRIPTION Product Standard EN 301 489-1 (09-2001), EN 301 489-17 (09-2000) EN 61000-4-2 Basic Standard, Specification, and Performance Criterion required Electrostatic Discharge ­ ESD: 8kV air discharge, 4kV Contact discharge, Performance Criterion B Radio-Frequency Electromagnetic Field Susceptibility Test ­ RS: 80-1000 / 1400-2000 MHz, 3V/m, 80% AM (1kHz), Performance Criterion A EN 61000-4-3 5. 2 GENERAL PERFORMANCE CRITERIA DESCRIPTION The Requirement of Performance Criteria Criterion A of the applicable class shall apply Performance criteria for 1 continuous phenomena applied to transmitters (CT) Performance criteria for Criterion B of the applicable class shall apply 2 transient phenomena applied to transmitters (TT) Criterion A of the applicable class shall apply Performance criteria for 3 continuous phenomena applied to receivers (CR) Performance criteria for Criterion B of the applicable class shall apply 4 transient phenomena applied to receivers (TR) Report No. : RM920221R04A Reference No. : RM920221R04 13 Issued: Mar. 14, 2003 The phenomena allowed during and after test in each criterion are clearly stated in the following table Performance criteria Criteria During test Shall operate as intended. May show degradation of performance (see note1). Shall be no unintentional transmissions. May show loss of function (one or more). May show degradation of performance (see note 1). Shall be no degradation of performance (see note 2). Shall be no loss of stored data or user programmable functions. Shall operate as intended after recovering. Shall be no degradation of performance (see note 2). Shall be no loss of stored data or user programmable functions. A B C May be loss of function (one or more). Functions shall be recoverable by the operator. Shall operate as intended after recovering. Shall be no degradation of performance (see note 2). NOTE 1:Degradation of performance during the test is understood as a degradation to a level not below a minimum performance level specified by the manufacturer for the use of the apparatus as intended. In some cases the specified minimum performance level may be replaced by a permissible degradation of performance. If the minimum performance level or the permissible performance degradation is not specified by the manufacturer then either of these may be derived from the product description and documentation (including leaflets and advertising) and what the user may reasonably expect from the apparatus if used as intended. NOTE 2: No degradation of performance after the test is understood as no degradation below a minimum performance level specified by the manufacturer for the use of the apparatus as intended. In some cases the specified minimum performance level may be replaced by a permissible degradation of performance. After the test no change of actual operating data or user retrievable data is allowed. If the minimum performance level or the permissible performance degradation is not specified by the manufacturer then either of these may be derived from the product description and documentation (including leaflets and advertising) and what the user may reasonably expect form the apparatus if used as intended. Report No. : RM920221R04A Reference No. : RM920221R04 14 Issued: Mar. 14, 2003 5. 3 EUT OPERATING CONDITION 1. [. . . ] 14, 2003 5. 5. 3 TEST PROCEDURE The test procedure was in accordance with EN 61000-4-3 a. The testing was performed in a fully-anechoic chamber. The transmit antenna was located at a distance of 3 meters from the EUT. The frequency range is swept from 80 MHz to 1000 MHz / 1400 MHz to 2000 MHz, with the signal 80% amplitude modulated with a 1kHz sinewave. [. . . ]