User manual BELKIN OMNIGUARDSOFTWARE6

[. . . ] OmniGuardTM UPS Power Management Software Version 1. 4 20th March 2003 OmniGuard TM UPS Power Management Software User Manual P74265 1 OmniGuardTM UPS Power Management Software 1. 0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. 0 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. 1 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. 2. 1 Computer interface connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. 0 Installation Procedure for Windows Versions . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4. 0 Starting OmniGuardT M services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5. 0 Useful Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 6. 0 OmniGuardT M Software for Linux and Solaris Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 7. 0 HP Openview Configuration for receiving Traps. . . . . . . . . . . . . . . . . . . 54 Recommended format setting: Received event $E. $# args: $* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Configure the SNMP Configuration in HP . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 2 OmniGuardTM UPS Power Management Software 1. 0 Introduction OmniGuardT M Power Management Software is a UPS environment control management application for Windows 95/98/ME, Windows NT, 2000, Linux and Solaris operating systems. OmniGuardT M Power Management Software monitors the UPS connected to the host system through a RS 232 serial cable with any remote system connected to this host through the Internet. Through the system's web browser, the user can monitor and change the host system's IP, Date, and System Name. [. . . ] Close the browser. Client: Show the device type. UPS: Including all detail information about OmniGuardT M UPS. 18 OmniGuardTM UPS Power Management Software If the UPS is not connected physically to the COM port, then you will see the screen below showing the Device Not Found message. The input voltage, Output Voltage, Battery charge level, Input frequency, Output Source, Output Load, Output power and the battery Temperature are displayed. These are information details, which are returned by the UPS. The values displayed ensure the proper connection is being established between the UPS and the host system. The details are logged in the data log. 19 OmniGuardTM UPS Power Management Software Identification The UPS identification details like manufacturer, model, software version and the Identification are displayed below. 20 OmniGuardTM UPS Power Management Software Configuration The configuration details are read from the UPS and displayed. Input/Output Voltage, frequency, Power, batter installed date, auto restart, etc. Parameters are displayed with live values from the UPS. The meter refresh interval is set in seconds. This time shall be set, for how frequently a user wants to refresh the UPS/meter data on this page. This functionality will work only when an Action is selected as "Enabled". Once OK is pressed, the above event is scheduled as per the set date and time, and shall be activated at this particular time only. 29 OmniGuardTM UPS Power Management Software View Graphic The View Graphic page displays the current values pertaining to the UPS. These values are configurable, and display the values indicated by the UPS. CAUTION!The very first time, you click View Log Graph, Status of Connection it will show Failure as default, indicating that no connection has been established. Please wait for few seconds, 15-20 seconds, until Connection status becomes OK from Failure. Click on Log Graph button, will take you to the below screen. 30 OmniGuardTM UPS Power Management Software After adjusting the axis dates with the left and bottom corner option arrows shown below, you will get a graph like the one below. Options are highlighted with arrow markings. 31 OmniGuardTM UPS Power Management Software View Data Log The data from the UPS, which is captured and logged, is displayed with this menu. After clicking ok, you will get actual data log as shown below. It is shown in two parts, due to the screen size. 32 OmniGuardTM UPS Power Management Software View Data Log 33 OmniGuardTM UPS Power Management Software After Ok is selected, this view will be displayed as seen below . . . 34 OmniGuardTM UPS Power Management Software Event Action The various events in the UPS can be configured through this option. A pager /broadcast /email can be sent if an alarm has occurred. Under the View Event Action option, there are many options that can be configured, as per the requirements of the end user. CAUTION!All event configurations are in the unchecked status initially. 35 OmniGuardTM UPS Power Management Software Pager Screen Options shown with a check are enabled. This must be done for certain events to take place such as the paging feature. 36 OmniGuardTM UPS Power Management Software Broadcast Screen If the below options are enabled, and the client IP Addresses are added using the Settings Screen shown earlier, it will send broadcast messages to all clients configured to receive the broadcast. 37 OmniGuardTM UPS Power Management Software Logging Screen 38 OmniGuardTM UPS Power Management Software Trap Screen Please specify the IP Addresses of Managers that are receiving traps. Trap Enable must be clicked to have traps received by managers. 39 OmniGuardTM UPS Power Management Software Email Screen Email messages will be sent as per configuration, when one of the events occurs in the configured event list. 40 OmniGuardTM UPS Power Management Software Command Screen 41 OmniGuardTM UPS Power Management Software Shutdown OS/UPS This option must be enabled to make the shutdown feature active. 42 OmniGuardTM UPS Power Management Software 5. 0 Useful Tips 1. If you receive the Device Not Found message even though the device is actually connected to COM port, Please check, ??Settings screen COM Port is correct Check COM port is working and not used by another application Check our DOS prompt, process for agent process as below The above screen must detect the UPS on the stated COM Port in order to receive the message, UPS Found. From here you can also confirm the detection of the UPS. [. . . ] Move any of ups MIB if already loaded till now. Open Event Configuration screen, delete all events under your ups MIB already loaded, and then remove Enterprise upsMIB. Note 2: All MIB developed for each device, are based on upsMIB. Because of this reason, it is must to remove first all events under upsMIB first, and then remove enterprise upsMIB itself. [. . . ]