User manual BELKIN P74521-B

[. . . ] Home Theater Power Conditioner PF30L, PF31L, and PF40L User Manual AP11000-10 AP11200-12 AP11201-12 Table of Contents Page PureAV Power Conditioner Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Power Conditioner Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Hookup and Installation Step 1 (optional) Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Mounting your Power Conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] C) with the mounting screws on the surface of the wall-mount bracket (Fig. Use the wall-mount bracket as a template to mark the four screw locations on the mounting surface (Fig. Drill 3/16" pilot holes in the screw locations. Insert the plastic drywall anchors into the pilot holes. Attach the wall-mount bracket with the #6 x 1" drywall screws. Mount the Power Conditioner to the mounting bracket (Fig. A) by aligning the mounting holes on the back of the Power Conditioner (Fig. C) with the mounting screws on the surface of the wall-mount bracket (Fig. B). Screw Locations Mounting Screws Fig. B (Screw Locations, Mounting Screws) Fig. C (Mounting Holes) Mounting Holes 6 Hookup and Installation Step 2 Connect Audio Components to the Audio Filter (switched) Certain components do not need to be, or should not be, powered on at all times. For this reason, the audio filter outlets are "switched" and can be controlled with the button situated on top of the Power Conditioner unit labeled "Switched". When you depress and hold this button for approximately two seconds, the "Switched On" light will illuminate and power will flow to the switched outlets. To turn off the switched outlets, simply push and hold the "Switched" button again until the "Switched On" light is extinguished. Power will stop flowing to the switched outlets. Attach PureAV power cord labels to each component's power cord before you plug the cord into the corresponding outlet on the Power Conditioner. Receiver (Preamp) ­ Connect your receiver or preamp power cord to the outlet labeled "Receiver". Tape ­ Connect your tape player power cord to the outlet labeled "Tape". CD ­ Connect your CD player power cord to the outlet labeled "CD". Auxiliary 01 ­ This outlet can be used to connect any other audio equipment you may have. Amp ­ Connect your main amplifier power cord to the outlet labeled "High Current AMP". This outlet is specifically designed to deliver high current to power-hungry amplifiers. [. . . ] · Your components may be plugged into a "Switched" outlet and the outlets are not switched on. Check to ensure that the green "Switched On" light on the top of the Power Conditioner is illuminated. If the light is not illuminated, press the "Switched" button on top of the Power Conditioner unit until the light is illuminated. You should now have power to all of the switched outlets. [. . . ]