User manual BELKIN RK1000

[. . . ] Proceed until all four casters contact the floor. Verify that you have received all hardware and components with your Belkin Enclosure. Contact Belkin support if you feel items are missing. Mounting hardware and keys can be found in bag attached to one of the vertical mounting rails. NOTE: Skid should be saved if you need to reship the Enclosure. [. . . ] Remove button plugs by pushing from the back side and retain for reuse. Remove latch bracket and door stops (2) using Phillips head screwdriver while holding lock nut in back. Turn and place bracket and door stops (2) on the opposite side (Figure D). Put push buttons back into holes on opposite side. NOTE: The best time to reverse the door is prior to installing the equipment. Standard factory door configuration is left-hand hinged. Figure B Figure A Remove handle and reverse Belkin Enclosure - User Manual v 1. 0. 0 Page 9 P74789 Reversing your Front Door Figure C Belkin Enclosure - User Manual v 1. 0. 0 Page 10 P74789 Reversing your Front Door Latch Bracket Door Stops Figure D Belkin Enclosure - User Manual v 1. 0. 0 Page 11 P74789 Adjusting your Vertical Mounting Rails The universal M6 cage nut rails are preset at a 29" depth. This depth allows for the installation of most rack-mountable equipment. Rails are infinitely adjustable front to back. The best time to move the rails is before installation of equipment. To adjust your rails, loosen the rail bolts (4) with a 7/16" hex socket. Vertical Mounting Rail Use a 7/16" Hex Socket to loosen bolt Full Depth Front to Rear Adjustability Belkin Enclosure - User Manual v 1. 0. 0 Page 12 P74789 Installing your Equipment All Belkin Enclosures conform to the 19" EIA 310-D industry standard. The vertical mounting rail has 42 Rack-Mount Units (RMU). An (RMU) consists of a 1. 75" vertical rack space. 31 1 RMU (1. 75") 30 · Load your rack from the bottom up, placing the heaviest components at the lowest position. · Please follow the individual instructions that are A provided with the components you are installing. · After installation of your equipment, extend only one component at a time. · For proper air flow, please use filler panels (optional) per component manufacturer recommendations. 29 Grounding Studs The ten grounding studs on the Enclosure are located on the doors, side panels, and frame. Number of studs 2 2 4 2 Location Base Front door Rear doors (2 each) Side panels (1 each) Please refer to part number RK5038 for the optional Belkin enclosure grounding kit. GROUND STUD : #10-32 x 1-7/8" LG. C MULTIPLE STRAPS Belkin Enclosure - User Manual v 1. 0. 0 Page 13 P74789 Cable Management Part Number Description Image RK5000 Vertical Lacing Bar RK5001 Waterfall Cable Manager RK5002 Vertical Finger Cable Manager RK5012 Double Sided 1U Cable Manager RK5013 RK5016 Double Sided 2U Cable Manager Single Sided Cable Manager RK5017 Low Density Cable Organizer Belkin Enclosure - User Manual v 1. 0. 0 Page 14 P74789 Cable Access 3 3/4" x 7 1/2" (2x) 2" Diameter (4x) 2 1/2" x 6" (4x) 3 3/4" x 9" (1x) 2" Diameter (4x) 13" x 21" (1x) Bottom Your Belkin Enclosure provides easy cable access. The top has two rectangular and four grommeted access points. The rear corner posts have two integrated cable knock-outs. These knock-outs can be removed when ganging two or more Enclosures together. These knock-outs will still allow you to have cabinet-to-cabinet access with a side panel in place. · Access through the bottom is achieved through one large center opening, an additional rectangular point in the rear and four grommeted access points. · · · · · Belkin Enclosure - User Manual v 1. 0. 0 Page 15 P74789 Specifications Description RK1000 RK1001 RK1002 Measurement Height with Casters (Standard) Width Depth 80. 25 in (203. 8 cm) 24 in (60. 96 cm) 42 in (106. 7 cm) 48. 75 in (123. 8 cm) 24 in (60. 96 cm) 42 in (106. 7 cm) Weight Shipping Weight Open Area Front Door 275 lbs. w/o sides (147. 9 kg) 830. 2 in2 (5356 cm2) 20. 5 in2 (132. 3 cm2) 19. 8 in2 (127. 7 cm2) 2200 lbs. [. . . ] Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. IN NO EVENT SHALL BELKIN CORPORATION BE LIABLE FOR INCIDENTAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH AS, BUT NOT LIMITED TO, LOST BUSINESS OR PROFITS ARISING OUT OF THE SALE OR USE OF ANY BELKIN ENCLOSURE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. This Warranty gives you specific legal rights, and you may also have other rights, which may vary from state to state. Some states do not allow the exclusion or limitation of incidental, consequential, or other damages, so the above limitations may not apply to you. Belkin Enclosure - User Manual v 1. 0. 0 Page 19 P74789 Contact Information www. belkin. com Belkin Corporation 501 West Walnut Street Compton, CA 90220, USA 310-898-1100 310-898-1111 fax Belkin Ltd. [. . . ]