User manual BELLO PVS4215 INSTALLATION

[. . . ] In order to provide you with timely assistance, please thoroughly inspect your furniture for missing or defective parts immediately after opening the carton. To receive replacement or missing part(s) under this warranty, go to our website at www. bello. com or call our Customer Service Department at 1-888-235-7646. Please have the model number and part number(s) for reference. You will also need your sales receipt or other proof of purchase. [. . . ] Except as provided herein, Bell'O International shall have no liability or responsibility to the purchaser or any other person or entity with respect to any liability, loss or damage caused directly or indirectly by use of the product, including, but not limited to, any incidental or consequential damages. Some states do not allow limitation on how long an implied warranty can last or the exclusion of limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights. You may also have other rights, which vary from state to state. PVS-4215 Flat Panel Television Stand ASSEMBLY INSTRUCTIONS BELL'O INTERNATIONAL CORPORATION, 711 Ginesi Drive, Morganville, NJ 07751-1235 Phone: (732) 972-1333 Fax: (732) 536-6482 Web: www. bello. com E-mail: sales@bello. com PATENT PENDING Parts List PART # TOOLS Assembly Instructions PART DESCRIPTION Cam Locks CMS® Panel Top Glass Shelf Middle Glass Shelf Bottom Glass Shelf Front Foot Cylinders Rear Foot Cylinders Middle Shelf Leg Cylinders Lower Shelf Leg Cylinders PART DESCRIPTION Allen Wrench Philips Screwdriver QTY. Wrench PART # 18 2 1 3 4 8 7 5 6 QTY. 2 1 1 1 1 2 2 2 2 NOTE: TWO PEOPLE ARE RECOMMENDED TO ASSEMBLE THIS TABLE. 13 17 9 12 14 15 16 10 11 Hex Nut Smaller Hex Head Screw Larger Hex Head Screw Cam Lock Pin Middle Shelf Support Post Bottom Shelf Support L-Bracket Plastic Cap Long Threaded Connection Rod Small Threaded Connection Rod 4 2 4 2 1 2 4 2 2 A. PLACE the Top (least deep) Glass Shelf (1) upside down, on a soft flat surface, with the silver discs facing upward. SCREW the two Cam Lock Pins (12) into the small silver discs located at the rear of the Shelf and tighten as shown in Fig. INSERT the CMS® (Cable Management System) Panel (2) onto the ends of the two Cam Lock Pins (12) with the Cam Locks (18) facing the rear 10 of the table. TIGHTEN the two Cam Locks using the Philips Screwdriver as shown in Fig. INSERT one end of the two Long Threaded Connection Rods (10) into each of the larger silver discs as shown in Fig. 1, and tighten using the supplied Wrench. SLIDE the two metal Middle Shelf Leg Cylinders (5) over the exposed ends of the Long Threaded Connection Rods (10). SCREW the Middle Shelf Support Post (14) into the pre-drilled hole located in the front center of the CMS® Panel (2) as shown in Fig. CAREFULLY SLIDE the Middle Glass Shelf (3) (the one without the silver discs) onto the Threaded Rods so that it is sitting on the end of the Cylinder, and PLACE the rear edge of the Middle Glass Shelf under the Shelf Support Post. SLIDE the two metal Lower Shelf Leg Cylinders (6) over the Threaded Rods (10) so that it is resting on the Middle Glass Shelf (3) as shown in Fig. SCREW the two Bottom Shelf Support L-Brackets (15) into the lower rear inside of the CMS® Panel (2) using the Larger Hex Head Screws (9) as shown in Fig. CAREFULLY place the front of the Bottom Glass Shelf (4), with the large silver discs positioned away from the CMS® Panel (2), onto the exposed end of the Threaded Rods (10), and POSITION the silver discs at the rear of the Bottom Shelf beneath the two Bottom Shelf Support L-Brackets (15) as shown in Fig. SECURE the small silver discs to the Shelf Support L-Brackets using the Smaller Hex Head Screws (17) as shown in Fig. NOTE: The table will be upside down at this point, so the bottom glass shelf will now be at the top of the table. PLACE the metal Rear Foot (taller) Cylinder (7) over the exposed ends of the Threaded Rods (10). [. . . ] ALWAYS REMOVE THE TV AND OTHER EQUIPMENT FROM THE FURNITURE PRIOR TO MOVING THE ASSEMBLED UNIT. BE CAREFUL WHEN MOVING THE ASSEMBLED FURNITURE AFTER THE GLASS SHELVES HAVE BEEN INSTALLED, AND/OR WHEN THERE IS EQUIPMENT LOCATED ON THE FURNITURE AS THIS MAY CAUSE THE SHELVES TO BECOME UNSECURED AND FALL. WHEN IN USE, THIS FURNITURE MUST BE PLACED ON A FLAT, SOLID AND LEVEL SURFACE. DO NOT LEAN ON THE TV WHEN IT IS ON THE TV STAND. [. . . ]