User manual BELSON RCI-6-15

[. . . ] That the water inlet and outlet hoses are connected correctly; 3. That the dishwasher is level on the ground. It is worth it: for the longer life span and the correct operation of your dishwasher. 13) Learn to get to know the parts which make up your dishwasher, you will use it better for it. [. . . ] 16 ARISTON DISHWASHER - Instructions for installation and use D ISHWASHER Select the right wash cycle A wash cycle for every degree of soil Salt, rinse aid, the right amount of detergent and the correct wash cycle: this is the formula to get the best results and to keep your dishwasher in shape Select the right wash cycle for your dishes. Selecting the most suitable wash cycle for the load ensures clean dishes and a more convenient use of water and electricity. & \ FOH & \ FOH V H OH F WLR Q LQV WUXF WLR QV & \ FOH GH V F ULSWLR Q ' H WH UJH QW IR U SUH  ZD V K  ZD V K 5 LQV H $ LG :D V K F\ F OH GXUD WLR Q WR OH UD QFH “   Very dirty d ishes and p ans (not to be used fo r delicate items) 6 XSH U :D V K C ycle fo r no rmally d irty p ans and d ishes.  ' D LO\ :D V K Environmentally- friend ly cycle, w ith low energy co nsump tio n levels, suitab le fo r normally d irty p ans and d ishes. s ho rt w ash at 4 7 °C H o t rinse at 6 5°C D rying  J  6 R D N LQJ P reliminary w ash cycle for dishes w hile aw aiting co mpletio n of the lo ad w ith the d ishes from the next meal. S pecial cycle to b e used fo r mo re d elicate items w hich are sensitive to high temp eratures. S ho rt co ld w ash to p revent fo o d from d rying onto the dishes  & U\ V WD O W ash at 52 °C Rinse at 45 °C H o t rinse at 6 5°C D rying  J  6 SH F LD O * XH V W Rinse and drying cycle for dishes that are seld o m used and are o nly dusty. h o t rinse at 6 5°C D rying  ARISTON DISHWASHER - Instructions for installation and use 17 D ISHWASHER Water in your home Loading the salt. Always use salt which is intended for dishwasher use. The salt container is situated underneath the lower rack, fill it up as follows: 1. Pull out the lower rack completely, unscrew and remove the container cap 2. Once the appliance is positioned, adjust the feet by screwing them in or out depending on how high you want it and to level it so that it is horizontal. Make sure that it is not inclined more than 2 degrees. If the appliance is level, it will he lp ensure its correct operation. Adjusting the Back Feet Insert the appliance into the cutout and then adjust the height using the screws located on the front bottom part of the machine. Use a screwdriver to turn the screws in the clockwise or anti-clockwise direction to increase or decrease the height respectively. Connect the cold water supply hose to a threaded 3/4 (gas) connector, inserting the small filter supplied with the dishwasher and making sure that it is fastened tightly in place (see figure 2). The LV460 A model, have a "Water Stop" water supply pipe, with filter in the threaded inlet If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance. Antinoise protection (where present) - On top of the dishwasher you will find two self-adhesive sponges. - Glue the small sponge onto the top cross-rod as shown in photograph 1. - Tilt the appliance and glue the large sponge as shown in photograph 2. [. . . ] Check the sprayer arms regularly and clean them once in a while. 1 B 2 A C Keep your dishwasher in shape Respecting these few rules ensures you will always have a reliable work companion by your side. When the wash cycle has ended, always remember to turn off the water supply tap and to leave the appliance door ajar. This way, moisture and bad odours will not be trapped inside. [. . . ]