User manual BENSHAW RS11

[. . . ] RediStart Micro II Computer Card Jumpers . 16 16 17 21 21 21 22 i TABLE OF CONTENTS 4. 26 27 31 31 32 33 33 34 35 35 36 37 38 38 40 5. 42 43 44 44 45 45 45 45 46 46 46 47 47 5. 2 PROGRAMMING: Quick Start . [. . . ] Values The decel level #1 is adjustable from 10% to 100% in 1% increments. The decel level #1 setting must be greater than the decel level #2 setting. The default value for the decel level #1 parameter is 40%. Default V Level #2 Description The V Level #2 parameter sets the ending voltage for the voltage ramp profile. Decel level #2 can not be set greater than decel level #1. The deceleration profile uses an open loop voltage ramp profile. The decel level #2 parameter sets the ending point on the S curve. This means that decel level #2 is not set as a percentage of actual line voltage. If the motor stops rotating before the deceleration time has expired, increase this parameter value. If the motor is still rotating when the deceleration time has expired, decrease this parameter value. A typical decel level #2 setting is between 10% and 20%. Values The decel level #2 parameter is adjustable from 1% to 99% in 1% increments. The default value for the Sense Time parameter is 0. 05 seconds. Values Default 58 5. 10 PROGRAMMING: Starter Setup - TruTorque Ramp Int Torque (initial torque) Description The initial torque parameter sets the initial torque level that the motor will produce during starting. This parameter should be set to a level that allows the motor to begin acceleration with a few seconds of a start command being received. The initial torque is adjustable from 1% to 100% in 1% increments. The default value for initial torque is 20%. Values Default Max Torque (maximum torque) Description The maximum torque parameter sets the final level of torque that is supplied to the motor during starting. For a loaded motor, the maximum torque parameter initially should be set to 100% or greater. If the maximum torque value is set too low, the motor may not produce enough torque to reach full speed (UTS). On a lightly loaded motor this parameter may be reduced below 100% to provide for smoother starts. The maximum torque is adjustable from 10% to 325% in 1% increments. The default value for the maximum torque parameter is 105%. Values Default Ramp Time Description The ramp time parameter sets the time it takes for the commanded torque to go from the Initial Torque Setting to the Maximum Torque Setting. To make the motor accelerate faster, decrease the ramp time. To make the motor accelerate slower, increase the ramp time. [. . . ] ONLY) 1 2 TBP10 SCR GATE 5 1 JP1 COMPUTER CARD RIBBON CABLE 2 1 TBP11 SCR GATE 3 LEDP3 SCR STATUS (LOW VOLT. ONLY) 1 2 3 4 5 6 7 8 1 2 SW1 SW2 (RIGHT - ON) TBP12 SCR GATE 6 TBP4 CURRENT TRANSFORMERS 1 2 3 TBP13 TACH. INPUT 112 7. 1 DRAWINGS RediStart Micro II Four (4) Relay Card Layout TB2 RELAY OUTPUTS 1 24 TB1 CARD POWER 1 2 J1 RIBBON CABLE CONNECTOR RediStart Micro II Seven (7) Relay Card Layout K1 Relay 1 2 3 K2 Relay 4 5 6 K3 Relay 7 8 9 K4 Relay 10 11 12 K5 Relay 13 14 15 K6 Relay 16 17 18 K7 Relay 19 20 21 K1 K2 K3 K4 K5 K6 K7 HOT 1 2 3 4 NEUTRAL FU1 J1 TB3 120Vac Connector J1 Ribbon Cable Connector 113 7. 1 DRAWINGS RediStart Micro II RS-232 Communications Card Layout RECEIVE LED TRANSMIT LED RIBBON CABLE CONNECTOR TO COMPUTER CARD LED1 RXD LED2 TXD RS-232 IC RS232 CARD J2 TB1 9-PIN SUB-D MALE DCE PINOUT RS-232 CONNECTORS TXD C COM RXD RediStart Micro II RS-485 Communications Card Layout RECEIVE LED TRANSMIT LED DRIVER ENABLE RIBBON CABLE CONNECTOR TO COMPUTER CARD LED1 RXD LED3 DE LED2 TXD RS485 CARD RS-485 IC TB1 J3 B(+) COM A(-) RS-485 CONNECTORS 9-PIN SUB-D FEMALE 114 7. 1 DRAWINGS RediStart Micro II RS-232/485 Communications Card Layout RIBBON CABLE CONNECTOR TO COMPUTER CARD TRANSMIT LED RECEIVE LED 120 OHM TERM SHIELD TO COM RS-485 CONFIGURATION SWITCHES RS-485 TERMINAL BLOCK RS-232 CONNECTOR 9 PIN, SUB-D, FEMALE DCE PINOUT Modbus Master Card (for Remote RTD Module) 24VDC FROM POWER CARD J3 Gnd+24V 24VDC POWER SUPPLY Com +24V J8 DE TxD RxD REMOTE RTD MODULE CONNECTOR A B Com Shield J6 D4 D5 D6 J7 CPU J1 Display J2 U3 RECEIVE TRANSMIT DEVICE ENABLE U6 CPU RIBBON CABLE CONNECTOR J5 U5 U7 DISPLAY RIBBON CABLE CONNECTOR 810007 02-00 U1 U4 D3 LED1 D2 LED2 UJ1 UJ2 VALID SLAVE RESPONSE STATUS 115 7. 1 DRAWINGS RediStart Micro II Display Cut-out 2 27/32" MICRO DISPLAY CUT-OUT TEMPLATE (May not print to scale) 2 15/16" CUT-OUT SIZE: 5-3/8" x 2-5/8" HOLE PATTERN: 5-11/16" x 2-15/16" HOLE SIZE: 3/16" 5 11/16" 116 8. PARAMETER LIST 8. 1 Parameter List RediStart Micro II Parameter List General The following pages list the menu parameters for the RediStart Micro II. The list gives the page number where information on the parameter can be found. [. . . ]