User manual BERNEX BN22208 CATALOGUE 2010

[. . . ] The drying programme is started by pressing the "Start (Pause)" button. Changing programme selection: If the programme selected is changed during drying, the dryer stops. The "Start (Pause)" indicator lamp flashes. To operate the new programme, again press the "Start (Pause)" button. [. . . ] To operate the new programme, again press the "Start (Pause)" button. Interrupting programme: To interrupt a drying cycle, press the "Start (Pause)" button and open the door. Wait at least 5 minutes, to allow the laundry to cool down, before you unload the dryer. For your safety the drying cycle stops automatically if you open the door. To restart, after door opening, close the door and press the "Start (Pause)" button again. Warning: Never stop a tumble dryer before the end of the drying cycle, unless all items are quickly removed and spread out so that the heat is dissipated. The final part of a tumble dryer cycle occurs without heat (cool down cycle) to ensure that the items are left at a temperature that ensures that the items will not be damaged. Starting dryer Programme end unloading dryer End: Take the laundry out of the dryer. The drying process is complete and the anti-crease phase has been reached (active). Anti-Crease: If the laundry is not removed at the end of the drying cycle, an automatic anti-crease cycle will operate for maximum 60 min. The drum rotates at regular intervals to prevent the laundry from creasing. Set the programme selector knob to " ". Switching dryer off Cleaning the lint filter: Open door, pull lint filter up and out of machine and open it. · Is the plug properly inserted into the mains electricity socket?· Has a drying programme been selected?· Has the "Start (Pause)" button been pressed?· Is the outside vent hose adaptor blocked? Drying takes too long laundry is not dry enough. . . . you want to check the dryer yourself first: (If your machine is not functioning correctly, please check the following points before phoning for the customer service ­ also refer to relevant chapter in the instructions for use). The dryer will not operate (after a power failure, always press the "Start (Pause)" button). Lint filter indicator lamp on. AFTER-SALES SERVICE If the fault is still present once the above checks have been undertaken or should the fault occur for a second time, switch the machine off. Please contact your after-sales service representative (for more information, refer to the warranty manual). Please have the following details ready when calling your after-sales service representative: · The nature of the fault. · The service code (the number after the word Service on the adhesive rating plate) on the right-hand side when the door is open. 3 Before using the machine, please also read the instructions for use carefully! AWZ 3520 Quick Reference Guide GB Programme selector knob The drying programme is selected by turning this knob. Programme sequence + Overdry protection Drying Anticrease End of cycle "Start (Pause)" button The drying programme is started by pressing this button. The indicator lamp flashes during the selection phase and lights up during drying. Options Gentle Reduces drying intensity (recommended for delicate items). Indicator lamps Filter The indicator lamp lights up when the filter needs cleaning. Clean the filter at the end of every cycle. Rapid Cotton Shortens drying duration (recommended for thin items of the same size). Time remaining display Depending on the programme selected, once the drying cycle has been started, a default drying time is displayed. [. . . ] The indicator lamp flashes during the selection phase and lights up during drying. Options Gentle Reduces drying intensity (recommended for delicate items). Indicator lamps Filter The indicator lamp lights up when the filter needs cleaning. Clean the filter at the end of every cycle. Rapid Cotton Shortens drying duration (recommended for thin items of the same size). Time remaining display Depending on the programme selected, once the drying cycle has been started, a default drying time is displayed. The time displayed is corrected by a few minutes depending on the volume, type and dampness of the laundry. The drying time specified is a calculated value which will be updated during the drying programme. Buzzer Signals/sounds end of drying cycle. Anti-crease The flashing lines indicate that the calculation is running. [. . . ]