User manual BERNEX BN22305 CATALOGUE 2010

[. . . ] You will find your model number on the left hand side wall of the refrigerator. Model # Serial # _ features safety information SAFETY INFORMATION WARNING • Before operating the appliance, please read this manual thoroughly and retain it for your reference. •B  ecause these following operating instructions cover various models, the characteristics of your refrigerator may differ slightly from those described in this manual. CAUTION/WARNING SYMBOLS USED Indicates that a danger of death or serious injury exists. WARNING WARNING Indicates that a risk of personal injury or material damage exists. CAUTION OTHER SYMBOLS USED Represents something you must NOT do. Represents something you must NOT disassemble. Represents something you must NOT touch. [. . . ] Make sure the water storage tank inside the refrigerator is properly filled. To do this, press the water dispenser lever until the water runs from the water outlet. Water Line installation Kits are included with unit. You can find it in freezer drawer. Installing the water dispenser line Parts for water line Installation Water line fixer and screws Pipe connector Water line Filter lock-clip Filter Connecting to the water supply line Connect the water pipe with coupler and tap. Connect coupler “A” to the tap. Note: WARRANTY INFORMATION This water line installation is not covered by the refrigerator or ice maker manufacturer’s warranty. Follow these instructions carefully to minimise the risk of expensive water damage. CAUTION The water line must be connected to the cold water pipe. If it is connected to the hot water pipe, it may cause the filter to malfunction. COUPLER “A” Note: If the coupler does not fit on the current tap, go the nearest authorised service dealer and purchase the right couplers fittings. TAP 18_ setting up setting up your side-by-side refrigerator LINE OUTLET 01 SETTING UP Select the location where the filter is to install. (Model with the filter) - If you wish to reassemble the water inlet and outlet sides of the filter during filter installation, see the reference illustration. - Cut the water line attached to the filter to the appropriate place after measuring the distance between the filter and the cold water tap. SIDE OF FILTER FILTER WATER 90 degree REFERENCE WATER INLET SIDE OF FILTER COUPLER Remove any residual matter inside the filter. (Model with the filter) - Open the main water tap to check whether water is running through the water tube on the water inlet side of the filter. 1. Place the refrigerator in an appropriate location with reasonable clearance between the wall and the refrigerator. Refer to installation instructions in this manual. . Once the refrigerator is plugged in, make sure the interior light comes on when you open the doors. . Set the temperature control to the coldest temperature and wait for an hour. The freezer should get slightly chilled and the motor should run smoothly. . After powering the refrigerator, it will take a few hours to reach the appropriate temperature. Once the refrigerator temperature is sufficiently cool, you can store food and drink in the refrigerator. USE ICE TRAY(OPTIONAL)(RSA1N, RSA2N, RSA1B) When the freeze temperature get zero degre below, you can use Ice Box to make ice. Pull out the ice tray. Place it inside ice tray. Pour cool water into the tray until it reaches the water level indicator on the tray. Turn ice tray button and the ice automatically full into the below ice compartment after release. Pull out ice storage compartment for ice. Place it under the freezer shelf or on the freezer shelf. Pull out the ice tray. Pour water into the tray until it reaches the water level indicator on the tray. To separate individual ice cubes, pull out the ice tray and hold the ice tray by its ends, then twist it gently. _ setting up OPERATING THE REFRIGERATOR Using the Control Panel RSA1J/D 02 OPERATING 1 5 6 2 3 4 RSA1N RSA1B 7 5 RSA2N 6 5 6 1 POWER FREEZE BUTTON FREEZER BUTTON ICE TYPE BUTTON FILTER CHANGE BUTTON POWER COOL BUTTON Speeds up the time needed to freeze products in the freezer. This can be helpful if you need to quickly freeze items that spoil easily or if the temperature in the freezer has warmed dramatically (For example, if the door was left open). Press the Freezer button to set the freezer to your desired temperature, You can set the temperature between -14°C (8°F) and -25ºC (-14°F). [. . . ] Condensation can occur when you leave the door open for a long time. • Did you wait for 12 hours after installation of the water supply line before making ice?• Is the water line connected and the shut-off valve open?• Did you manually stop the ice making function? [. . . ]