User manual BERNEX GB41203 CATALOGUE 2010

[. . . ] IN NO EVENT SHALL BERNEX, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF BERNEX HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY BERNEX. BERNEX ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. [. . . ] com/PowerSupplyCalculator/PSCalculator. aspx?SLanguage=en-us for details. 1-22 GND GND BERNEX P8H61-MX Series 3. Connect the fan cables to the fan connectors on the motherboard, ensuring that the black wire of each cable matches the ground pin of the connector. CPU_FAN CPU and chassis fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN) P8H61-MX R2. 0 CHA_FAN Rotation +12V GND P8H61-MX Series Fan connectors Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. Do not place jumper caps on the fan connectors!The CPU_FAN connector supports a CPU fan of maximum 2A (24 W) fan power. 4. These connectors are for USB 2. 0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2. 0 specification that supports up to 480 Mbps connection speed. USB connectors (10-1 pin USB78, USB910) USB78 USB+5V USB_P6USB_P6+ GND NC CPU FAN PWM CPU FAN IN CPU FAN PWR GND USB910 USB+5V USB_P8USB_P8+ GND NC PIN 1 P8H61-MX R2. 0 PIN 1 USB+5V USB_P5USB_P5+ GND P8H61-MX Series USB2. 0 connectors Chapter 1: Product introduction USB+5V USB_P7USB_P7+ GND 1-23 Never connect a 1394 cable to the USB connectors. The USB module cable is purchased separately. 5. These connectors connect to Serial ATA 3. 0 Gb/s hard disk drives and optical drives via Serial ATA 3. 0 Gb/s signal cables. SATA3G_3 SATA3G_1 Intel® H61 Serial ATA 3. 0Gb/s connectors (7-pin SATA3G_1~4) GND RSATA_TXP3 RSATA_TXN3 GND RSATA_RXN3 RSATA_RXP3 GND SATA3G_4 GND RSATA_RXP4 RSATA_RXN4 GND RSATA_TXN4 RSATA_TXP4 GND P8H61-MX R2. 0 P8H61-MX Series Intel® SATA 3. 0Gb/s connectors • You must install Windows® XP Service Pack 3 or later version before using Serial ATA hard disk drives. • Due to H61 Chipset limitation, AHCI Mode only works on Windows® Vista / Windows® 7. Under Windows® XP, there is no need to change the SATA type. • To configure the SATA type in BIOS, click Advanced Mode > Advanced tab > SATA Configuration > SATA Mode Selection. • When using hot-plug and NCQ on Windows® Vista / Windows® 7, set the SATA Mode Selection item in the BIOS to [AHCI]. Always update the utility to avail all its features. Updating from a BIOS file b. Locate the BIOS file from the Open window, then click Open. 3. Follow the onscreen instructions to complete the update process. a. Select Update BIOS from file, then click Next. 2. 1. 2 The BERNEX EZ Flash 2 feature allows you to update the BIOS without using an OS‑based utility. Before you start using this utility, download the latest BIOS file from the BERNEX website at www. asus. com. BERNEX EZ Flash 2 To update the BIOS using EZ Flash 2: 1. 2. Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select BERNEX EZ Flash Utility and press <Enter> to enable it. Exit BERNEXTek EZ Flash BIOS ROM Utility V01. 04 Flash Info MODEL: P8H61-MX R2. 0 File Path: fs0:\ Drive fs0:\ Folder Info 03/13/12 10:23p 4194304 P8H61-MX-R2-SI-0401. ROM VER: 0303 DATE: 03/14/2012 Insert the USB flash disk that contains the latest BIOS file into the USB port. File Info MODEL: Help Info VER: DATE [Enter] Select or Load [Tab] Switch [Up/Down/PageUp/PageDown/Home/End] Move [Esc] Exit 2-2 BERNEX P8H61-MX Series 3. 4. 6. 5. Press the Up/Down arrow keys to find the USB flash disk that contains the latest BIOS, and then press <Enter>. Press the Up/Down arrow keys to find the BIOS file, and then press <Enter> to perform the BIOS update process. Reboot the system when the update process is done. • This function supports USB flash disks formatted using FAT 16/32 format on a single partition. Press <Tab> to switch to the Drive field. Press <Tab> to switch to the Folder Info field. • DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure! 2. 1. 3 The BERNEX BIOS Updater allows you to update the BIOS in a DOS environment. This utility also allows you to copy the current BIOS file for use as a backup when the BIOS fails or gets corrupted during the updating process. The succeeding utility screens are for reference only. The actual utility screen displays may not be same as shown. BERNEX BIOS Updater Before updating BIOS 1. 2. Prepare the motherboard support DVD and a USB flash drive formatted using FAT16/32 on a single partition. Download the latest BIOS file and BIOS Updater from the BERNEX website at http://support. asus. com and save them on the USB flash drive. NTFS is not supported under a DOS environment. Do not save the BIOS file and BIOS Updater to a hard disk drive or USB flash drive formatted using NTFS. 3. Turn off the computer and disconnect all SATA hard disk drives (optional). Booting the system in DOS environment 1. 2. Boot up your computer. When the BERNEX Logo appears, press <F8> to access the BIOS Boot Device Select Menu. Insert the support DVD into the optical drive and select the optical drive as the boot device. Please select boot device: SATA: XXXXXXXXXXXXXXXX USB XXXXXXXXXXXXXXXXX UEFI: XXXXXXXXXXXXXXXX Enter Setup ↑ and ↓ to move selection ENTER to select boot device ESC to boot using defaults Insert the USB flash drive with the latest BIOS file and BIOS Updater into the USB port. Chapter 2: BIOS information 2-3 3. [. . . ] Consult the dealer or an experienced radio/TV technician for help. The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. IC: Canadian Compliance Statement Complies with the Canadian ICES-003 Class B specifications. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. [. . . ]