User manual BESELER 23C ENLARGER

[. . . ] If this equipment does cause interference to radio or television reception (which can be determined by turning the equipment on and off), the user is encouraged to attempt to correct the interference by following the following steps: Reorient the antenna of the radio or television Relocate the computer with respect to the radio or television receiver Plug the computer into a different power outlet so that the computer and receiver are on different electrical branch circuits. If necessary, the user should consult with the dealer or an experienced radio/television technician for additional help and suggestions. The user may find the following booklet, prepared by the FCC, helpful in solving radio/television interference problems: "How to Identify and Resolve Radio-TV Interference Problems" This booklet is available by sending a written request to: U. S. Government Printing Office Washington D. C. , 20402 Request Stock Number 004-000-0345-4. ECC Statement This device complies with the requirements of EEC directive 89/336/EEC with regard to Electromagnetic Compatibility. [. . . ] 4 . . @n IP Company Contents Checklist 1. PenCam 2. Application / Driver CD Driver & Application 3. Install Quick Guide 4. USB Cable NOTE: If you are missing any of these contents please inform your dealer or your nearest support office so that the contents can be replaced. . . 5 . . Ins ta ic Qu l uid kG e System Requirements Microsoft Windows XP/ 98 / ME / 2000 Pentinum 200 MHz (or equivalent) processor or higher 32 MB of RAM (64 MB recommended) Video card with 2 MB of RAM for minimum 16 bit (High Color) display 4X speed CD-ROM An available USB port Specifications Sensor type: Color VGA(640x480)CMOS image sensor Iamge Performance for Video Stream: 9 fps for QVGA(320x240 Pixels) 3 fps for VGA(640x480 Pixels) Memory & Images (SDRAM 64Mbit): 26 Picture for VGA(640x480 Pixels), 107Pictures for QVGA(320x240 Pixels) Dimension:5. 6 " x1. 35 "x1 " Battery: AAA1. 5V x2 battery Lens view angle: 54 Degrees Interface type: USB Port Software Support: Microsoft Windows XP/ 98/ME/2000 Operating Environment The camera should be operated only within the following environmental conditions: 41-104 Fahrenheit; 5-40 Celsius 20% - 85% relative humidity, non-condensing PenCam Cautions!Never immerse any part of the PenCam or its components into any fluid or liquid. Disconnect the PenCam from your computer before cleaning it. Remove dust or stains with a soft cloth dampened with water or neutral detergent. Do not use any volatile chemicals or liquids such as thinner or benzene to clean the PenCam. Do not place hot items on the surface of the PenCam. Do not attempt to disassemble the PenCam. . . 6 . . @n IP Company How to Use Your PenCam Introduction The camera is capable of taking and storing VGA(640x480 Pixels) images or QVGA(320x240 Pixels) Images. These images may be uploaded to a PC via the USB port. User Interface The camera has two switches on it. SW1 is the shutter switch. SW2 is the mode switch. The camera may be used like this without any batteries. However, all pictures will be lost when the USB connector is unplugged. To start using the PenCam Manager, simply click on the "Start" menu and go up to "Programs" Then go to the folder named "PenCam" and select it. This is the program where you can begin to use your camera. . . 12 . . @n IP Company Mode Selecting = Press the "Live View" button to switch the camera to PC Camera mode. = Press the "DSC Function" button to switch the camera to DSC & Camcorder mode. Live View (PC Camera Mode) DSC Function (DSC Mode) PC Camera Mode In this mode, it is easy to attach the camera to your system, to use as a stand PC camera. the current view is displayed in the "preview" window. = Press "Video Source" button to adjust advanced setings. = Press "Video Format" button to set image size. = Press "Snap Shot" button to capture an image to album folder. = Press "Record button" to recording a video clip to album folder. . . 13 . . DSC Mode Uploading Photos: This allows you to upload photos captured by the camera. [. . . ] The Limited Warranty cannot be transferred to another individual from the original purchaser, except as provided in the END-USER LICENSE AGREEMENT. If the HARDWARE PRODUCT is sold to another user by the original End-User, the Limited Warranty will be null and void, and BESELER will have no obligation to provide the Warranty Service. If the HARDWARE PRODUCT is a gift from the original purchaser to another person, then the Limited Warranty can be transferred to the recipient of the HARDWARE PRODUCT, provided the original purchaser does not attempt to open the box which the HARDWARE PRODUCT was packaged in. If this HARDWARE PRODUCT is purchased from an unauthorized reseller, the Limited Warranty will be null and void, and BESELER will have no obligation to provide the Warranty Service. [. . . ]