User manual BIAMP COLUMBIA SERIES

[. . . ] If a control item includes a volume control assignment, the bottom of the display will show a graphical representation of a volume bar with the current level indicated to the right (percentage of maximum level). Capacitive-touch Scroll Wheel The capacitive-touch sensor provides a sleek interface for menu navigation and selection. The glossy-finish finger groove allows for scrolling through and selecting available control items, as well as adjusting volume. 4 COLUMBIA SERIES bAck pANEl Connectors Two Ethernet connectors--one rear-facing RJ45 and one top-facing insulation displacement connector (IDC)--are provided for connecting to the network. The RJ45 and IDC utilize unshielded twisted pair (UTP) wiring to connect to an Audia or Nexia system. [. . . ] Please note: many of the configuration settings can be accessed via the Audia or Nexia software. Locksmith: Bridge jumper pins to enter setup mode The cursor has two modes: select and modify. In select mode, the cursor appears as a gray box. When scrolling through the available items in the list, the gray box will highlight the current selection. "Select" mode in device setup menu On fields that can be modified, use the Select button to transition to and from modify mode. In modify mode, the cursor appears as an outline box. Use the scroll wheel to adjust the setting up or down. "Modify" mode in device setup menu Some screens have additional buttons that are used to accept (OK), reset, or cancel changed settings. Use the scroll wheel to navigate the cursor to these buttons and press the Select button. The OK button saves the setting and exits the screen. The Reset button clears the setting and does not save it. The Cancel button exits the screen without saving the setting. 6 COLUMBIA SERIES sEt Up Edit Device ID To name the unit, scroll to the ID Tag icon and press the Select button. Use the scroll wheel and Select button to choose the desired characters. The Device ID must match that of a corresponding block in the Audia or Nexia design. See the figures below. 11. 75cm 4 5/8 4 3/4 12. 07cm Wall cut out dimensions Mounting using a SECTION A-A back box RacoTM 254 Mounting using theA-A SECTION retro-fit plate 10 COLUMBIA SERIES INstAllAtION Retro-Fit Plate RacoTM 254 Trim Ring Front Plate Exploded view showing pieces required for mounting to the retro-fit plate or the RacoTM 254 back-box When installing the COLUMBIA SERIESF using the retro-fit plate or the back-box, fasten the trim ring using the four screws provided to either the retrofit plate or the back-box. Once the trim ring has been fastened to the retro-fit plate or the back-box, guide the COLUMBIA SERIESF front plate at an angle into the top of the trim ring to seat the tabs on the top of the front plate. (100m) Ethernet cable length can be extended with standard PoE network technology 128 24 Standard Ethernet network wiring Each control configured for specific operation by the system design software EU Directive 2002/95/EC, RoHS Directive CE marked FCC SPECIFICATIONS (COLUMBIA SERIESF) Dimensions Power consumption Control cable requirements Control cable length Control wiring topology Control programming Compliance 6. 22"H x 5. 82"W x 0. 5"D (158mm x 148mm x 12. 7mm) PoE Class 1 (3. 2W @ full display utilization) CAT-5/6/7 Ethernet cable using either RJ-45 or IDC connector 330' (100m) Ethernet cable length can be extended with standard PoE network technology Standard Ethernet network wiring Each control configured for specific operation by the system design software EU RoHS Directive 2002/95/EC; CE; FCC 13 COLUMBIA SERIES wARRANty BIAMP SYSTEMS IS PLEASED TO EXTEND THE FOLLOWING 5-YEAR LIMITED WARRANTY TO THE ORIGINAL PURCHASER OF THE PROFESSIONAL SOUND EQUIPMENT DESCRIBED IN THIS MANUAL 1. BIAMP Systems warrants to the original purchaser of new products that the product will be free from defects in material and workmanship for a period of 5 YEARS from the date of purchase from an authorized BIAMP Systems dealer, subject to the terms and conditions set forth below. 2 If you notify BIAMP during the warranty period that a BIAMP Systems product fails to comply with the warranty, BIAMP Systems will repair or replace, at BIAMP Systems' option, the nonconforming product. As a condition to receiving the benefits of this warranty, you must provide BIAMP Systems with documentation that establishes that you were the original purchaser of the products. Such evidence may consist of your sales receipt from an authorized BIAMP Systems dealer. Transportation and insurance charges to and from the BIAMP Systems factory for warranty service shall be your responsibility. This warranty will be VOID if the serial number has been removed or defaced; or if the product has been altered, subjected to damage, abuse or rental usage, repaired by any person not authorized by BIAMP Systems to make repairs; or installed in any manner that does not comply with BIAMP Systems' recommendations. Electro-mechanical fans, electrolytic capacitors, gooseneck microphones, cords connecting handheld microphones, hard-drives, displays, and normal wear and tear of items such as paint, knobs, handles, keypads and covers are not covered under this warranty. All server-based devices are warranted for 3 years only. [. . . ] No agent, employee, distributor or dealer of BIAMP Systems is authorized to modify this warranty or to make additional warranties on behalf of BIAMP Systems. Statements, representations or warranties made by any dealer do not constitute warranties by BIAMP Systems. BIAMP Systems shall not be responsible or liable for any statement, representation or warranty made by any dealer or other person. No action for breach of this warranty may be commenced more than one year after the expiration of this warranty. [. . . ]