User manual BIAMP CPA 130

[. . . ] When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. [. . . ] Exclamation Point: Replace components (i. e. fuses) only with the values specified by the manufacturer. Failure to do so will compromise safe operation of this unit. For more complete instructions, see the software Help file, or the printable Help documument (on CD). Nexia Quick Start Connecting to stand alone Nexia device Each Nexia unit comes loaded with a default system configuration. Follow steps 1-7 for connecting to a Nexia default configuration. To create and load your own custom configuration, follow steps 1-5 and then go to step 10. Install Nexia software on a Windows® 2000/XP Professional PC PC must have a 10/100baseT NIC. Assign IP address to PC Each Nexia device ships from the factory with a default IP address of 192. 168. 1. 101. PC must have a unique IP address before it can communicate with a Nexia device. Right Click My Network>Properties>Local Area Connection>Right Click Properties>TCP/IP>Properties IP address should be 192. 168. 1. x (x=1-254 except 101 because that is what Nexia is set to. ) Subnet mask should be 255. 255. 255. 0 Click Ok when complete Close My Network 2. 3. Power up Nexia devices Connect supplied power cord to a grounded AC mains voltage of 100-240VAC @50/60Hz. Connect other end of power cord to power entrance located on the rear of Nexia unit. Under normal conditions, all LEDs will remain green once power-up sequence has completed. 4. Connect PC to Nexia unit Connect "cross-over" Ethernet cable (supplied with unit) from PC 10/100baseT Ethernet jack to Ethernet jack located on rear panel of Nexia unit. File>Network>Connect to network Close when complete 9. Assign IP address to Nexia device All Nexia units ship from the factory with an assigned IP address of 192. 168. 1. 101. When using more than one device in a system, each device must have a unique IP address. Nexia device IP addresses must be different from any PC IP address that will be used in this system. File>Network>Perform Nexia Device Maintenance>Select desired Audia device>Set IP address IP address should be 192. 168. 1. x (x=1-254) Subnet mask should be 255. 255. 255. 0 Default gateway should be 0. 0. 0. 0 Click Ok when complete Close Device Maintenance when complete Note: To avoid conflict issues that occur when connecting multiple Nexia devices with the same IP number, be sure to only connect one Nexia device at a time to the Ethernet switch when assigning IP addresses. Repeat steps 6-8 until all Nexia devices in system have been connected to network and assigned a unique IP address. 11. Reset/Initialize each Nexia unit Because each Nexia unit ships from the factory with a default system configuration, you must first reset/initialize that unit before loading our own configuration. File>Network>Perform Nexia Device Maintenance>Reset/Initialize each connected Nexia unit 12. Connect NexLink For multi-unit systems, "straight-through" Cat-5 cables must be connected from the appropriate rear panel NexLink TX jack(s) to the appropriate NexLink RX jack(s) according to the layout of your design. Check the compile results to verify correct NexLink connections. Open layout (. nex) file File>Open>Select file 13. 14. Enter appropriate Nexia unit serial numbers to equipment table Tools>Equipment table>Select appropriate serial numbers Select OK when complete 15. Send Configuration File>Network>Send System Configuration Sends layout configuration to selected Nexia unit. 16. Start Audio Upon loading configuration, select the option to start audio 17. Adjust component parameters as needed Optional: 18. Disconnect PC from Nexia system File>Network>Disconnect from Nexia system Disconnect PC from Network File>Network>Disconnect from network 19. WARRANTY BIAMP SYSTEMS IS PLEASED TO EXTEND THE FOLLOWING 5-YEAR LIMITED WARRANTY TO THE ORIGINAL PURCHASER OF THE PROFESSIONAL SOUND EQUIPMENT DESCRIBED IN THIS MANUAL 1. BIAMP Systems warrants to the original purchaser of new products that the product will be free from defects in material and workmanship for a period of 5 YEARS from the date of purchase from an authorized BIAMP Systems dealer, subject to the terms and conditions set forth below. If you notify BIAMP during the warranty period that a BIAMP Systems product fails to comply with the warranty, BIAMP Systems will repair or replace, at BIAMP Systems' option, the nonconforming product. [. . . ] Such evidence may consist of your sales receipt from an authorized BIAMP Systems dealer. Transportation and insurance charges to and from the BIAMP Systems factory for warranty service shall be your responsibility. This warranty will be VOID if the serial number has been removed or defaced; or if the product has been altered, subjected to damage, abuse or rental usage, repaired by any person not authorized by BIAMP Systems to make repairs; or installed in any manner that does not comply with BIAMP Systems' recommendations. Electro-mechanical fans, electrolytic capacitors, and normal wear and tear of items such as paint, knobs, handles, and covers are not covered under this warranty. [. . . ]