User manual BIAMP DJ 3600, 3500, 3001

[. . . ] Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] When the LED remains lit, the amplifier has an over-temperature condition. When the LED is flashing, the amplifier has an output fault condition. Either condition will temporarily de-activate the amplifier, causing the Signal / Peak LED to turn off as well. The amplifier will attempt to self-reset once the over-temperature or output fault condition is resolved. This indicator also appears on the rear panel. CAUTION: The DJ 3600, 3500, 3001 is cooled by a variable speed fan, which exhausts warm air from the left side panel. To allow proper ventilation, an un-obstructed clearance of at least 0. 75" must be maintained along the left side panel of the DJ 3600, 3500, 3001. 6 REAR PANEL C UL R WARNING: SHOCK HAZARD - DO NOT OPEN US LISTED 52SJ NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DJ 3600, 3500, 3001 Class 2 Wiring xfmr output direct output BIAMP SYSTEMS Designed in Oregon, U. S. A. Assembled in India AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR E215636 CAUTION I CAUTION: Risk of fire replace fuse only with same type T 6. 3 A L 250 V RISK OF ELECTRICAL SHOCK. DO NOT OPEN. Use only with a 250V fuse Employer uniquement avec un fusible de 250V signal / peak temp / fault UNBAL 775mV OFF level O BAL 300mV HPF ~120V 60Hz 900 Watts 8 70V 25V 25V CT COM OUT XFMR INPUT 4 GND input Input: This plug-in barrier strip provides the line-level input to the amplifier. HPF Switch: This DIP switch provides a High-Pass Filter for the amplifier input. The High-Pass Filter is used to eliminate unnecessary lower frequencies (12dB/octave @ 125Hz) for speech and distributed speaker applications. From the factory, the High-Pass Filter is enabled (switch down). To disable the High-Pass Filter, move the switch to the up position. CAUTION: To avoid output fault conditions, the High-Pass Filter must be enabled when driving 25/70 Volt speaker systems (see Output below). Also, any other system equalization affecting frequencies below 125 Hz should remain flat or be used as cut-only. 775mV / 300mV Switch: This DIP switch selects 0. 775Vrms (0dBu) or 0. 3Vrms (-8dBu) as input sensitivity for the amplifier. From the factory, input sensitivity is set for 775mV (switch up). Use the 775mV setting for 'professional' line-level input signals (such as from an audio mixer or processor), or use the 300mV setting for 'consumer' line-level signals (such as from a CD player or tape deck). UNBAL / BAL Switch: This DIP switch selects unbalanced or balanced input connection. From the factory, input connection is set for UNBAL (switch up). [. . . ] Such evidence may consist of your sales receipt from an authorized BIAMP Systems dealer. Transportation and insurance charges to and from the BIAMP Systems factory for warranty service shall be your responsibility. This warranty will be VOID if the serial number has been removed or defaced; or if the product has been altered, subjected to damage, abuse or rental usage, repaired by any person not authorized by BIAMP Systems to make repairs; or installed in any manner that does not comply with BIAMP Systems' recommendations. Electro-mechanical fans, electrolytic capacitors, and normal wear and tear of items such as paint, knobs, handles, and covers are not covered under this warranty. 5. [. . . ]