User manual BIAMP KEYBOARD MIXER 44

[. . . ] Columns one through eight correspond to the eight amplifier module slots. The remaining LEDs correspond to the AudiaFUSION chassis. System Indicators alarm activity signal 1 signal 2 status ais power Channel Indicators Chassis Indicators Channel Indicators Alarm is a two-color LED that illuminates when a channel fault has occurred. Two types of channel faults can be reported, depending on the severity of the problem. [. . . ] Standby only occurs when a unit has been designated as a secondary failover device in the configuration. A red LED indicates a configuration load failure. Status is a tri-color LED that indicates the health of the AudiaFUSION hardware. A green LED indicates that the unit powered up normally. A flashing amber LED is shown briefly during the power-on self test and should turn solid green upon a successful start up. A red LED indicates that the unit experienced a problem during the power-on self test. AIS has no function at this time and is in place for possible future use. Power is a green LED that illuminates when power is applied to the unit. 5 AudiaFUSION REAR PANEl Figure 3 . Rear Panel Layout 10 SERIAL CONTROL PORT Audia FUSION chassis composite (Pantone Black) 6/30/09 BG 9 Class 2 Wiring 1234 8 7 6 5 4 3 2 1 AM-600 AM-600 AM-600 AM-600 AM-600 AM-600 AM-600 MODEL AudiaFUSION CAUTION RISK OF ELECTRICAL SHOCK. DO NOT OPEN. FUSE FUSE Primary 220-240V: T 12 H, 250V 110-120V: T 20 H, 250V Ethernet 110-120/220-240V~ 115V 50/60Hz 2400WATT CobraNet® Connections Only YEL: In use/Conductor GRN: Link/Activity NM-1 OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT AM-600 OUTPUT Class 2 Wiring Class 2 Wiring BIAMP SYSTEMS Logic I/O Class 2 Wiring Class 2 Wiring Class 2 Wiring Class 2 Wiring Class 2 Wiring 52SJ Serial Control Port After initial programming and configuration, AudiaFUSION may be controlled by third-party control systems such as AMX® or Crestron® using the Serial Control Port. External devices may also be controlled or signaled via the Serial Control Port by utilizing Command String blocks within the Audia system design. CobraNet The CobraNet interface in AudiaFUSION supports up to 32 simultaneous channels of digital audio (16-in, 16-out) over Fast Ethernet and is compatible with other CobraNet compliant devices. Failover is triggered by one of the following conditions: · Chassis alarm · Channel alarm · Loss of power · Loss of CobraNet link · Loss of Logic I/O Only alarms (e. g. , heat sink alarm and channel failure alarm) trigger the failover mechanism. Warnings indicate abnormal system conditions that do not immediately impair audio and do not trigger the failover mechanism. The redundant amplifier must have the same configuration as the primary amplifier (i. e. , amplifier module count, watts per module, load configuration). A wire failover link cable must be connected between the primary and the redundant amplifier as shown below. Connect ground to ground and logic 4 of the primary amplifier to logic 3 of the redundant amplifier; connect logic 3 of the primary amplifier to logic 4 of the redundant amplifier. Leave logic 1 and 2 disconnected. 1234 Class 2 Wiring The redundant amplifier can be wired in parallel to the existing speaker line or connected to a redundant speaker line (see figure below). Relays isolate the output terminals on the secondary AudiaFUSION unit. When a configuration is received, relays close on the primary AudiaFUSION and remain open on the redundant AudiaFUSION. On failover, the relay positions are reversed. Parallel Wiring Primary AudiaFUSION Redundant Wiring Primary AudiaFUSION Redundant AudiaFUSION Redundant AudiaFUSION After replacing the faulty amplifier, a power cycle is required to recover from failover. The primary device will resume control after the fail condition is cleared and the unit is re-powered. 8 Class 2 Wiring 1234 Primary AudiaFUSION Logic I/O Redundant AudiaFUSION Logic I/O AudiaFUSION REAR PANEl Channel-to-Channel Failover In addition to entire amplifier failover, AudiaFUSION supports channel-to-channel failover, which is triggered by one of the following conditions: · Heat Sink alarm · Short Circuit alarm* · Channel Failure alarm The wire failover link cable is not required when wiring channel-to-channel failover. [. . . ] This warranty is in lieu of all other warranties, expressed or implied. Biamp Systems disclaims all other warranties, expressed or implied, including, but not limited to, implied warranties of merchantability and fitness for a particular purpose. The remedies set forth herein shall be the purchaser's sole and exclusive remedies with respect to any defective product. No agent, employee, distributor or dealer of BIAMP Systems is authorized to modify this warranty or to make additional warranties on behalf of BIAMP Systems. [. . . ]