User manual BIAMP MIXPAK

[. . . ] If the wiring is identical on both ends, it is a "straight through" Ethernet cable. 7. Connect Audia device to network Connect one Audia device to network using "straight through" Ethernet cable attached from the rear panel Ethernet jack to the 10/100baseT Ethernet switch. 8. Connect to network with Audia software Open Audia software then connect to network. File>Network>Connect to network Close when complete 9. [. . . ] Assign IP address to Audia device All Audia units ship from the factory with an assigned IP address of 192. 168. 1. 101. When using more than one device in a system, each device must have a unique IP address. Audia device IP addresses must be different from any PC IP address that will be used in this system. File>Network>Perform Audia Device Maintenance>Select desired Audia device>Set IP address IP address should be 192. 168. 1. x (x=1-254) Subnet mask should be 255. 255. 255. 0 Default gateway should be 0. 0. 0. 0 Click Ok when complete Close Device Maintenance when complete Note: To avoid conflict issues that occur when connecting multiple Audia devices with the same IP number, be sure to only connect one Audia device at a time to the Ethernet switch when assigning IP addresses. 10. Repeat steps 6-8 until all Audia devices in system have been connected to network and assigned a unique IP address. 11. Connect CobraNet For multi-unit systems, "straight-through" Ethernet cables must be connected from the rear panel CobraNet jack of each unit to a 10/100baseT Ethernet switch. 12. Open layout (. dap) file File>Open>Select file 13. Enter appropriate Audia unit serial numbers to equipment table Tools>Equipment table>Select desired Audia unit(s) Select OK when complete 14. Send Configuration File>Network>Send System Configuration Sends layout configuration to selected Audia unit(s). 15. Start Audio 16. Adjust component parameters as needed Optional: 17. Disconnect PC from Audia system File>Network>Disconnect from Audia system 18. Disconnect PC from Network File>Network>Disconnect from network Connecting to stand alone unit using Audia without CobraNet (AudiaSOLO) 1. Install Audia software on a Windows® 2000/XP Professional PC PC must have a 10/100baseT NIC. 2. Design and Layout system Launch Audia software. If you notify BIAMP during the warranty period that a BIAMP Systems product fails to comply with the warranty, BIAMP Systems will repair or replace, at BIAMP Systems' option, the nonconforming product. As a condition to receiving the benefits of this warranty, you must provide BIAMP Systems with documentation that establishes that you were the original purchaser of the products. Such evidence may consist of your sales receipt from an authorized BIAMP Systems dealer. Transportation and insurance charges to and from the BIAMP Systems factory for warranty service shall be your responsibility. This warranty will be VOID if the serial number has been removed or defaced; or if the product has been altered, subjected to damage, abuse or rental usage, repaired by any person not authorized by BIAMP Systems to make repairs; or installed in any manner that does not comply with BIAMP Systems' recommendations. Electro-mechanical fans, electrolytic capacitors, gooseneck microphones, cords connecting handheld microphones, hard-drives, displays, and normal wear and tear of items such as paint, knobs, handles, keypads and covers are not covered under this warranty. All server-based devices are warranted for 3 years only. This warranty is in lieu of all other warranties, expressed or implied. BIAMP Systems disclaims all other warranties, expressed or implied, including, but not limited to, implied warranties of merchantability and fitness for a particular purpose. [. . . ] BIAMP Systems disclaims all other warranties, expressed or implied, including, but not limited to, implied warranties of merchantability and fitness for a particular purpose. The remedies set forth herein shall be the purchaser's sole and exclusive remedies with respect to any defective product. No agent, employee, distributor or dealer of BIAMP Systems is authorized to modify this warranty or to make additional warranties on behalf of BIAMP Systems. Statements, representations or warranties made by any dealer do not constitute warranties by BIAMP Systems. [. . . ]