User manual BINATONE 921A

[. . . ] Note: After lifting the handset you will need to wait for several seconds to get dial tone, before keying in the telephone number to make the call. Also you cannot dial numbers from memories when the mains power is off. *** Before operating this set, please read these instructions carefully. If you need help . . . . . Binatone Helpline (for UK only) Monday to Friday from 9:00am to 5:00pm Tel: 0845 345 9677 **Please note that all calls are charged at local rate Or visit our website: http://www. binatoneonline. com Unpacking your CC2310 system In the box, you will find: the base unit telephone a telephone line cable for the base unit a mains power adapter for the base unit the cordless handset (up to five, depending on which CC2310 system you've bought) two 1. 2V 550mA rechargeable batteries and a battery compartment cover for each handset up to five charger pods, each with a mains power supply for multi handset systems two user guides, one for the corded phone and one for the cordless handset. Keep the packaging materials in a safe place in case you later need to transport the unit. [. . . ] The Answer and Record mode allows a caller to leave a message, and is set when OGM1 (Out Going Message 1) is selected. The Answer Only mode, does not allow a caller to leave a message, and is set when OGM2 (Out Going Message 2) is selected. The answering machine is supplied with pre-set announcements for OGM1 and OGM2, but you can record your own personal announcements if you wish. When the answering machine is ON it will answer after a set number of rings (default 5), but you can change the number of rings if you wish. When the answering machine is OFF, or if the memory is full, it will answer after 15 rings, which allows remote access if required. Switching TAM on/off 1. By Hotkey (1) Switch TAM on to OGM 1 or OGM 2 . If the TAM is turned off, the display will show "TAM OFF" 12:00 TAM OFF 9/08 To Set up a three-way conference Binatone Help Line : 0845 345 9677 25 Press and hold STOP/ON/OFF for over 2 seconds to switch TAM on. Then you can see "OGM 1" on the display and hear the voice prompt "Answer ON, Announcement One". After this, the display will show the number of messages. 12:00 9/08 00/02 MSGS You can switch between OGM 1 and OGM 2 by pressing STOP/ON/OFF briefly, provided the TAM is already ON. (2) Switch TAM off If the TAM is already switched on, either with OGM 1 or OGM 2. Press and hold STOP/ON/OFF for over 2 seconds to switch the TAM off. Press the MENU/OK/MUTE to show "PHONEBOOK". Press the UP button to show "TAM", and then the MENU/OK/MUTE button to select it. Binatone Help Line : 0845 345 9677 27 Press the UP button to show "TAM SETTINGS". Press the MENU/OK/MUTE button to show "TAM ON/OFF". Press the DOWN button to show "SET OGM". Press the MENU/OK/MUTE button to show "OGM1" or Press the UP or DOWN button to choose "OGM1" or "OGM2" Press the MENU/OK/MUTE button to select it and show "PLAY". Press the DOWN button to show "RECORD". Press the MENU/OK/MUTE button to hear a voice prompt "PLEASE RECORD NEW ANNOUNCEMENT AFTER THE BEEP". After a beep tone you can start speaking. When you want to end the recording, press STOP/ON/OFF. Then the unit will playback the OGM announcement automatically. To playback the OGM 1. By Hotkey Press the REWIND/OGM briefly to listen to the current OGM (OGM 1 or OGM 2). 2. By MENU Press the MENU/OK/MUTE button to show "PHONEBOOK". [. . . ] If the call does not work, and you are using a two-way socket adapter, remove it and plug a telephone directly into the socket. If the call now works, the adapter may be faulty. If you cannot make a call, the fault may be on the exchange line. Contact the service provider (the BT engineers on 151 for UK only, or your cable company). [. . . ]