User manual BINATONE BIG BUTTON 510 SYSTEM

[. . . ] USER GUIDE Big Button 510 System Digital Cordless Telephones Extra large buttons and display THIS EQUIPMENT IS NOT DESIGNED FOR MAKING EMERGENCY TELEPHONE CALLS WHEN THE POWER FAILS. ALTERNATIVE ARRANGEMENTS SHOULD BE MADE FOR ACCESS TO DIAL EMERGENCY SERVICES. Ver. 1, Mar, 05 Before operating this set, please read these instructions carefully. BINATONE " Big Button 510 System " User Guide - Back Page BINATONE " Big Button 510 System " User Guide - Front Page 1)White background and black letters 2)Material: 100lb Double face art paper 3) Size: 105mm(w) x 148mm(H) A6 Color profile: Generic CMYK printer profile Composite Default screen Important note -- emergency calls The Big Button 510 is not designed for making emergency calls when the mains power fails. So you should make alternative arrangements for access to Emergency Services. [. . . ] But we do not guarantee that all features or display messages will be available using other manufacturers' equipment. 1 Follow the instructions in the base unit's User Guide to put the base unit into registration mode (for example, step 1 on page 20). 2 Follow the instructions in the handset's User Guide to register the handset (for example, steps 2 to 5 on page 20). If you need to enter a PIN code for the base unit, refer to the base unit's User Guide. If you have problems, contact the Binatone Help Line for more advice. 22 E:\Binatone2005\BigButton510\BigButton510_01. vp 27 February 2005 16:59:13 Color profile: Generic CMYK printer profile Composite Default screen Customising your handset General points You can customise the settings of your Big Button 510 handset, using a menu which is shown on the handset's display. Please note that: If you don't press any button for about 25 seconds, the handset will time out and the display will return to standby mode. When you confirm any setting you have made, you'll hear a confirmation tone. If you make a mistake, you'll hear a warning tone. At the end of each set of steps, you can return the handset to standby mode by either: -- replacing the handset on the base unit -- pressing and holding the HANG UP/C button Auto-answer When a call comes in, you need to press any button to answer it. Or you can set auto-answer -- so, if the handset is in place on the base unit, you simply lift it to answer the call, without pressing any button. 1 Press the PROG button then 1 5 2 Use the or button to set: 0 for auto-answer off 1 for auto-answer on Press the PHONE/OK button to confirm 3 Binatone Help Line: 0845 345 9677 (Local Call rate) 23 E:\Binatone2005\BigButton510\BigButton510_01. vp 27 February 2005 16:59:13 Color profile: Generic CMYK printer profile Composite Default screen Customising your handset Ringer volume and melody The handset has eight ringer volume levels, including 0 for off; and eight ringer melodies. With the volume set to 0, the handset will not ring for an incoming call, but the display will show call or the phone number. To change the volume: 1 Press the PROG button then 1 1 1 2 3 Use the or button to change the volume Press the PHONE/OK button to confirm To change the melody: 1 Press the PROG button then 1 1 2 2 3 Key tone Use the or button to change the melody Press the PHONE/OK button to confirm Normally, whenever you press a button on the handset, you hear a `beep' tone. You can turn these tones off if you prefer. 1 Press the PROG button then 1 1 3 2 Use the or buttons to set: 0 for key tone off 1 for key tone on Press the PHONE/OK button to confirm 3 24 E:\Binatone2005\BigButton510\BigButton510_01. vp 27 February 2005 16:59:13 Color profile: Generic CMYK printer profile Composite Default screen Customising your handset Direct Call With Direct Call turned on, when you press any key except the PROG button, the handset will automatically make a call to a number you have programmed in. This feature is sometimes called babysitter's call. ! With Direct Call turned on, it is not possible to make emergency calls, unless you have programmed an emergency number such as 999 as the Direct Call number. But remember that the number you have programmed will be dialled automatically when any key is pressed. Before you can turn Direct Call on, you must program the telephone number. 1 Press the PROG button then 1 3 2 Key in the number You can press the HANG UP/C button to clear digits one by one; or press and hold the HANG UP/C button to clear the Direct Call number completely. Press the PHONE/OK button to confirm To turn Direct Call on and off: 3 1 Press the PROG button then 1 2 2 Use the or buttons to set: 0 for Direct Call off 1 for Direct Call on Press the PHONE/OK button to confirm While Direct Call is turned on, the display shows and the Direct Call number. You can answer calls as normal. 3 Binatone Help Line: 0845 345 9677 (Local Call rate) 25 E:\Binatone2005\BigButton510\BigButton510_01. vp 27 February 2005 16:59:13 Color profile: Generic CMYK printer profile Composite Default screen Customising your handset To clear all memories This is a way of clearing all stored numbers at once, from the memory locations and the Last Number Redial memories. If you have set a Direct Call number, it will be cleared too. 1 Press the PROG button then 1 9 2 Press the PHONE/OK button to confirm Note: Caller ID memories are cleared by resetting the base unit (see page 31). To reset the handset When you reset the handset, you return all its settings to their defaults, as follows: 7 ringer volume ringer melody 4 key tone on Indirect Network off (see page 32) auto-answer off select base unit automatic (best connection) 1 Press the PROG button then 1 0 2 Press the PHONE/OK button to confirm 26 E:\Binatone2005\BigButton510\BigButton510_01. vp 27 February 2005 16:59:13 Color profile: Generic CMYK printer profile Composite Default screen Customising your base unit General points You can customise the settings of your Big Button 510 base unit, using a menu which is shown on the handset's display. Please note that: If you don't press any button for about 25 seconds, the handset will time out and the display will return to standby mode. When you confirm any setting you have made, you'll hear a confirmation tone. If you make a mistake, you'll hear a warning tone. [. . . ] If the call does not work, and you are using a two-way socket adapter, remove it and plug a telephone directly into the socket. If the call now works, the adapter may be faulty. If you cannot make a call, the fault may be on the exchange line. Contact the service provider (the BT engineers on 151, or your cable company). [. . . ]