User manual BINATONE FUSION 2200

[. . . ] 10 Intercom, transfer & conference If you have a Fusion 2200/2210 Twin, Triple or Quad system, you already have two, three or four handsets. You can buy spare handsets and charger pods separately. Altogether, you can have up to five handsets registered to the base unit, as numbers 2, 3, 4 and 5. With more than one handset registered to your base unit, you can make intercom calls from one handset to another, make a new intercom call while you are on an outside call shuttle between an outside call and an intercom call transfer an outside call from one handset to another set up a three-way conference call between yourself, an outside call and an intercom call Each handset has its own number -- 1, 2, 3, 4 or 5 -- which is shown on the right-hand side of the display. [. . . ] It will help if you have your PBX work properly on documentation to hand when you make the call. a PBX. " Intercom and transfer Move the handset closer to the base unit, or to a different position. Try moving the base unit so that it's not near other electrical equipment, such as a TV or a computer. If you are using a routing box (smart socket), try disconnecting it then making a call. If the sound is OK without the routing box, that's the cause of the problem. You'll get the best results if you site the base unit as high as possible. For example, in a two-storey house, the first-floor landing is an ideal place for the base unit. The strange noise is caused by interference. Disconnect the mains power lead from the back of the base unit, then wait for 30 seconds before reconnecting it. "I can't transfer a call. " Make sure the other handset is within range of the base unit, and is not busy on a call. Make sure you are keying in the correct number (1 to 5) for the other handset. If the fault persists . . . Disconnect all other instruments connected to the same line as the Fusion 2200/2210 and see whether you can make a call. Batteries "The handset`s batteries are running low within an hour or two. " "The CHARGE light on the base unit does not come on. " Before you first used the handset, you should have left it on the base unit or charger pod for up to 15 hours to charge the batteries fully. You may need to replace the batteries Clean the battery charging contacts with a dry cloth. Check the connections between the base unit and the mains power socket. 26 Disconnect the base unit from the telephone line and plug a different phone into the master telephone socket. If the call does not work, and you are using a two-way socket adapter, remove it and plug a telephone directly into the socket. If the call now works, the adapter may be faulty. If you cannot make a call, the fault may be on the exchange line. Contact the service provider (the BT engineers on 151, or your cable company). If you still cannot identify the cause of the problem, contact the Binatone Help Line on 0845 345 9677 Calls are charged at Local Call rate. 27 24 25 14 Answering machine Quick Reference (Fusion 2210 only) For detailed information on how to operate the answering machine, see the separate sheet. Shortcut buttons To control answering machine functions, you first press the button (also labelled R). You can then scroll through the menus for the function you want, and press to select it. Alternatively, some of the numbered buttons also give you shortcuts for OK functions you often use. Just press the button followed by the numbered button, as shown here. 15 Guarantee and service The Binatone Fusion 2200/2210 is guaranteed for 12 months from the date of purchase shown on your sales receipt. The Guarantee does not cover damage by misuse or negligence, or by excessive voltages -- for example, faults on the telephone line, or lightning. [. . . ] Press C 1 Press MEM 2 Press or 3 Press PHONE until the display shows the name or number or SPEAKERPHONE 7 once again to un-mute the mouthpiece 6 to dial the number You'll see either names or numbers. If you see a name displayed, to check the number and the time of the call: 3 Press OK OK once then press it again to show the time When you reach the beginning or end of the list of records, you'll hear a warning `beep'. Once you've checked all the records, the symbol will disappear from the display and the IN USE light will stop flashing. 8 9 6 Tones and volumes 1 Press OK To adjust the earpiece or speakerphone volume during a call OK to show the current volume level à 1 to 5 to change the volume OK Handset ringing volume You have a choice of five volume levels or of turning the ringer off. à phonebk 1 Press MENU Key tone on/off Each time you press a key, you hear a tone. à phonebk à handset 1 Press MENU then 7 Call barring Using call barring, you can prevent certain types of call being made on your handset. [. . . ]