User manual BINATONE T430

[. . . ] User Manual T430 Camera Navigation software for PNA UK English April , 2008 Important Safety Instructions The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION 1. To reduce the risk of electric shock, do not remove the cover (or back). Refer servicing to qualified service personnel. [. . . ] While navigating a route, these fields show the estimated time needed to reach the destination (ETE), the distance to destination, and the estimated arrival time at the destination (ETA) by default. You can choose what to display in these three fields during navigation, by going to Advanced settings / Display Options (Page 100). See the following list for your options. The only restriction is that you cannot select a value that already appears in another field. The possible field contents are: · · · · · · · · Distance to destination (default value for the left field) Time to destination (estimated time en route, default value for the middle field) Distance to next via point Time to next via point Time to next manoeuvre (next route event) Speed Speed limit Arrival at next via point 66 · Arrival at destination (default value for the right field) 4. 5. 16 Distance to next turn (No. 18) This field shows the distance to go before reaching the next route event (turn, roundabout, exit, etc. ) This field is only displayed when navigating a route. 4. 5. 17 Next street / Next settlement (No. 19) This field shows the road or street that comes next in the route itinerary. If you are not yet in the settlement where this next street is, Binatone Navigator will display the name of the settlement instead of the name of the road or street. A bullet symbol will appear next to the name of settlements to help you tell them apart from street names. This field is only displayed when navigating a route. 4. 5. 18 Approaching next turn (No. 20) This bar is only visible when approaching the next route event. It appears on the screen to visualise the distance when you get closer than 300 meters (1000 feet) to the next turn, and it remains visible till you reach the turn. This field is displayed only when navigating a route. 4. 6 Route Information screen The Route Information screen has all the data and some of the functions you need while you navigate. Some additional functions can be found in the Route menu (Page 77). Without an active route one of the buttons is inactive and route data cannot be displayed. As a reminder, you can open this screen two ways: tapping the Info button in the Route menu (Page 81), or tapping one of the Route Data fields on the Cockpit screen. 67 4. 6. 1 Route data displayed (for destination and via points) In the top section of the screen you see information about the current route. These fields are continuously updated while you keep this screen open. When you open the screen, all fields contain information on reaching your final destination. Tap any of the fields to see data on the via points starting from the first one through the final destination again. 4. 6. 1. 1 Route line The upper part of this screen shows your planned route as a horizontal line. Its leftmost point is the start of the route, the rightmost one is the final destination, and you can see your via point flags along the line, spaced in proportion to their distance. The blue (yellow when using night colours) arrow representing your position will travel from the left to the right, giving you visual feedback of your journey. When you reach a via point, it becomes the starting point of the route, the past will be deleted, the line with all the other via points will be modified instantly, and the arrow jumps back to the left. When Binatone Navigator needs to recalculate the route, the arrow will not jump back to the left as when reaching a via point, but it may drift a bit as the length of the new route may be different from the previous one. [. . . ] However, if the software product is operational after installation without the use of the original media copy, then the original media copy is deemed to be a security copy. In all other cases, the User is only entitled to use the security copy if the original media 125 copy of the software product has become unsuitable for proper and legal use without any doubt, such state thereof being supported by acceptable proof. to multiply the software product (to make a copy thereof); 7. 1. 2. to lease, rent, lend, distribute, transfer it to a third person with or without a consideration; 7. 1. 3. [. . . ]