User manual BISSELL 3750

[. . . ] ug603-5539_3750E_304 6/25/04 2:08 PM Page 1 Lift-OffTM BAGLESS USER'S GUIDE 3750 SERIES-220/240V 3 Safety Instructions 4 Product Diagram 5-6 Assembly 6-8 Operations / Special Tools 9-13 Maintenance 14 Troubleshooting 15 15 16 Consumer Services Replacement Parts Warranty ug603-5539_3750E_304 6/25/04 2:08 PM Page 2 Thanks for buying a BISSELL Lift-OffTM We're glad you purchased a BISSELL Lift-Off Vacuum. Everything we know about floor care went into the design and construction of this powerful, high-tech home vacuuming system. Your BISSELL Lift-Off is well made, and we back it with a limited comprehensive two-year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you'll receive fast, considerate assistance. [. . . ] Stair Cleaning Tool: Use for stairs, area rugs, and other small carpeted areas. This tool can also be used for bare floors. Telescoping Extension Wand: Use with desired attachment for a longer reach. To extend the Wand, twist the collar to "Unlock" position and push away from you. Twist the collar to the "Lock" position to lock into place. To retract, twist to unlock, pull toward you and twist to relock. All items may not be included with your model. More tools are available; to order please refer to page 15. CAUTION: cleaner on Always place vacuum floor in its fully Upright Position and make sure it is locked into place before removing Cylinder or when using tools. Placing the Lift-Off in its full Upright Position automatically stops the rotating brush. 7 ug603-5539_3750E_304 6/25/04 2:08 PM Page 8 Cleaning With The Detachable Cylinder The Detachable Cylinder feature makes it possible to easily take the powerful cleaning action of your BISSELL Lift-Off to stairways, auto interiors, and other hard-to-reach areas of your home. Before detaching the Cylinder, your Lift-Off must be in its fully Upright Position. You do not need to turn off the power first. Press the Release Button at the top of the Cylinder Handle and lift the Cylinder to remove. Release Button 1. 2. 5. Detach the Vacuum Hose from the Hose Grip Base at the back of the Cylinder. Attach the desired tool(s) to the Hose Grip at the end of the Vacuum Hose. When you're done, remove the tool(s) and reconnect the Hose to the Hose Grip Base. Return the Cylinder to the Powerfoot by aligning the "feet" on the front with the bumps on the foot of the Upright Vacuum. Push the Cylinder toward the vacuum frame until it "clicks" into place. NOTICE: certain While vacuuming, Power Cord Storage When you are done using your BISSELL Lift-Off, return it to the Upright position and store the Power Cord. Turn vacuum cleaner off (O). carpets and low humidity conditions may generate small static discharges. The discharges are entirely harmless and are not associated in any way with the main power supply. 1. 3. Unplug Power Cord by grasping the plug (NOT the cord) and disconnect from outlet. Loop Power Cord around Cord Wraps on side of the Cylinder. Transporting Cleaner 1. 2. To move your vacuum cleaner from room to room, put the Handle in the Upright Position, tilt the cleaner back on its rear wheels and push forward. [. . . ] If the thermal protector continues to activate after following the above steps, your cleaner may need servicing. NOTE: The thermal protector controls the main vacuum motor only, not the brush motor. If the thermal protector activates, the brush will continue to operate normally; however, there will be no suction. CAUTION: To reduce the risk of injury from moving parts, turn Power Switch OFF and disconnect plug from electrical outlet. 13 ug603-5539_3750E_304 6/25/04 2:08 PM Page 14 Troubleshooting Vacuum cleaner won't run. Possible Causes 1 2 Remedies 1 2 Power Cord not firmly plugged in Thermal protector activated Check electrical plug Allow cleaner to cool for 30 minutes, see pg. 13 No Power at Rotating Floor Brush. Possible Causes 1 2 Remedies 1 2 Cylinder is not securely seated Brush Switch turned to "OFF" Remove Cylinder and replace, making sure that it "clicks" into place Make sure Brush Switch is in "ON" position Vacuum cleaner or Tools won't pick up dirt. Possible Causes 1 2 3 4 5 6 7 8 9 10 Remedies 1 2 3 4 5 6 7 8 9 10 Incorrect Height Adjustment Hose not attached to suction opening Crack or hole in Hose Drive Belt broken, worn or off motor pulley Rotating Floor Brush bristles worn Rotating Floor Brush jammed Clog in vacuum Dirt Container full Dirt Container or Upper Tank not installed properly Filters are dirty Adjust Powerfoot to correct height setting Grasp Hose Grip and firmly push onto the base Check Hose and replace if needed Reposition or replace Drive Belt, see pg. [. . . ]