User manual BISSELL 3920

[. . . ] Pet Hair EraserTM BAGLESS VACUUM USER'S GUIDE 3920 SERIES 220-240V 3 Safety Instructions Product View Assembly Operations Maintenance and Care Troubleshooting Consumer Services Replacement Parts Warranty 4 5-6 6-10 10-16 17 18 19 20 ug110-4048_3920E_508. indd 1 5/7/08 3:56:50 PM Thanks for buying a BISSELL Vacuum We're glad you purchased a BISSELL vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your BISSELL vacuum is well made, and we back it with a limited one year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you'll receive fast, considerate assistance. [. . . ] Unplug the vacuum from electrical outlet 2. 2. 4. Slide the Lock `n Seal Lever to the "Unlock" position. Grasp handle and pull the dirt container straight out to remove from the vacuum. Empty dirt into garbage container. NOTE: Emptying the dirt container after every use will help prevent over filling and ensure that the vacuum is ready to go the next time you clean. Unlock 4. Cleaning the pre-motor and replacing the post-motor HEPA media filter 1. Unplug the vacuum from electrical outlet. The pre-motor filter protects the motor from dirt particles. It is located in the slide out tray underneath the dirt container. If the filter becomes dirty, pull out the tray, lift out the foam filter pad and clean it. NOTE: The pre-motor filter may be hand washed in cold water with mild Washable detergent. Rinse well and air dry Pre-Motor thoroughly before replacing. Filter The post-motor HEPA media filter assists in the filtration process to return clean air to the room. It is located behind the door on the side of the vacuum. If the filter becomes dirty, open the door, remove the filter and replace. NOTE: The post-motor filter is a white, pleated HEPA media filter. This filter is not washable and must be replaced when it becomes dirty. Post-Motor HEPA Media Filter 3. WARNING: Do not operate vacuum cleaner with damp or wet filters or without all filters in place. www. bissell. com 11 5/7/08 3:57:01 PM ug110-4048_3920E_508. indd 11 Maintenance and care Check rotating floor brush and drive belt You should check your vacuum cleaner's rotating floor brush and drive belt regularly for wear or damage. You should also clean the brush and brush ends of strings, hair and carpet fibers. This type of debris can wrap around the brush and hamper its ability to effectively clean your carpet. Also remove any debris that has accumulated under the brush cover. Unplug the vacuum from electrical outlet. 3. WARNING:injury To reduce the risk of from moving parts, turn vacuum cleaner off and disconnect power plug from electrical outlet. 2. Place handle in low position and turn vacuum cleaner over so bottom side is facing up. Remove the screws marked 1 and 2, Release the latches marked 3 and 4. Grasp rotating floor brush at both ends and lift. Clean strings, hair and other debris from rotating floor brush, paying particular attention to brush ends. [. . . ] Check pre-motor and post-motor filters for correct installation 3. Pull out and re-insert dirt container correctly Other maintenance or service not included in the manual should be performed by an authorized service representative. Thank you for selecting a BISSELL product. Please do not return this product to the store. 17 5/7/08 3:57:10 PM www. bissell. com ug110-4048_3920E_508. indd 17 BISSELL Consumer Services If your BISSELL product should require service: In the UK, Australia or New Zealand, call BISSELL Consumer Services at the numbers below and we will give you the location of a BISSELL Authorized Service Center in your area. For all other countries, contact your local in country distributor for questions, service, or repair. If you have questions about your warranty or need replacement parts please contact the numbers below. For UK inquiries: Monday - Thursday 9 am -- 5 pm Friday 9 am -- 4 pm BISSELL Homecare (Overseas) Inc. [. . . ]