User manual BISSELL 6860

[. . . ] R E V O L U T I O NTM Lift-Off TM 3760/4220/6850/6860 SERIES 3 4 Safety Instructions USER'S GUIDE Product Diagram 4-6 Assembly Instructions 6-9 Operation / Special Tools 10-13 Maintenance 14 15 15 16 Warranty Troubleshooting Replacement Parts Consumer Services Thanks For Buying A BISSELL Lift-OffTM RevolutionTM We're glad you purchased a BISSELL Vacuum. Everything we know about floor care went into the design and construction of this powerful, high-tech home vacuuming system. Your BISSELL Vacuum is well made, and we back it with a limited comprehensive one-year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you'll receive fast, considerate assistance. [. . . ] Attach the desired tool(s) to the Hose Grip at the end of 4. When you're done, remove the tool(s) and reconnect the Hose to the Hose Grip Base. 5. Return the Canister to the Powerfoot by aligning the "feet" on the front with the bumps on the foot of the Upright Vacuum. Push the Canister toward the vacuum frame until it "clicks" into place. Clean Filter Indicator Select Models Only The Clean Filter Indicator tells you when airflow in the vacuum is reduced due to dirty filters or a clog in the hose. The Clean Filter Indicator will remain green until the airflow is reduced. At that time, it begins to change to red. When it is fully red, the airflow is significantly reduced or blocked. Follow the steps on pages 10 -11 to clean your filters. The Canister could detach causing the rest of the vacuum to fall. CAUTION: Button Do not press the Release 2. The cleaner can also be moved by using the Carrying Handle Carrying Handle 9 How to Maintain Your Vacuum To maintain maximum cleaning performance, the following maintenance steps must be performed: 1. Empty the Dirt Container when the dirt reaches the "Full" line on the front. 2. Check the Upper Tank and Pre-Motor Filters at least once a month and clean and replace as needed. 3. Replace the HEPA Media Post-Motor Filter every six months. To reduce the risk of electric shock, turn Power Switch OFF and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks. WARNING: NOTE: More frequent filter cleaning may be necessary if you are vacuuming new carpet, fine dust, or have allergy concerns. Follow the instructions on the following pages to perform these simple maintenance steps. Tip: For maximum cleaning performance, check and clean or replace all filters as suggested. Empty Dirt Container The Dirt Container needs to be emptied when the dirt reaches the "Full" line on the front of the Container. 1. Slide the Lock `n Seal Lever to the "Unlock" position. Grasp handle and pull the Dirt Container straight out to Full Line Unlock Position Lock Position remove from vacuum. 4. Empty dirt into garbage container. 5. Put the Dirt Container back in the vacuum and slide the lever to the "Lock" position. Note: The Screens may also be removed from the side Dust Chambers when you empty or clean the Dirt Container. The Screens are made to fit each Dust Chamber. If they do not slide down completely, try in the opposite Dust Chamber. The Screens will also not fit if there is debris in the track. [. . . ] Note: The thermal protector controls the main vacuum motor only, not the brush motor. If the thermal protector activates, the brush will continue to operate normally; however, there will be no suction. Caution: of To reduce the risk injury from moving parts, turn off vacuum cleaner and disconnect Power Plug from electrical outlet. 13 Troubleshooting WARNING:injury from To reduce the risk of Vacuum cleaner won't run Possible Causes 1 Power cord not plugged in 2 Blown fuse/tripped breaker 3 Thermal protector activated moving parts and/ or electrical shock, turn Power Switch OFF and disconnect polarized plug from electrical outlet before performing troubleshooting checks. Remedies 1 Check electrical plug 2 Check/Replace fuse or reset breaker 3 Allow cleaner to cool for 30 minutes, see pg. 13 No Power at Rotating Floor Brush Possible Causes 1 Canister is not securely seated 2 Brush Switch turned to "Off" 3 Vacuum is in upright position Remedies 1 Remove Canister and replace, making sure that it "clicks" into place 2 Make sure Brush Switch is in "On" position 3 Recline vacuum to operate brush Vacuum cleaner won't pick up dirt Possible Causes 1 Incorrect Height Adjustment 2 Hose not attached to suction opening 3 Crack or hole in Hose 4 Drive Belt broken, worn or off motor pulley 5 Rotating Floor Brush bristles worn 6 Rotating Floor Brush jammed 7 Clog in vacuum 8 Dirt Container full 9 Dirt Container or Upper Tank not installed properly 10 Filters are dirty Remedies 1 Adjust Powerfoot to correct height setting 2 Grasp Hose Grip and firmly push onto the base 3 Check Hose and replace if needed 4 Reposition or replace Drive Belt, see pg. 11-12 5 Replace brush 6 Remove brush and clean debris from brush ends 7 Follow instructions on pg. [. . . ]