User manual BISSELL CLEANALONG 48K2

[. . . ] Do not pull or carry by cord, use cord as a handle, close door on cord, pull cord around sharp corners, run cleaner over cord, or expose cord to heated surfaces. Hold plug when rewinding the cord onto the reel. Do not allow the plug to whip when rewinding. Do not use cleaner if it has been dropped, damaged, left outdoors or dropped into water. [. . . ] crevice tool: Usethecrevicetoolintight, narrowspaces. 6 www. bissell. ca 1-800-263-2535 Operations Power cord the power cord is located at the rear of the vacuum. Gently pull out the power cord, watching for the yellow line. Stop pulling the power cord once the yellow line is visible. there is also a red line, which indicates the end of the usable cord. Do not pull the power Automatic cord out beyond the red line. Cord Rewind Button Automatic cord rewind your vacuum is equipped with an automatic cord rewind. When cleaning is finished, press the power button off and grasp the plug to disconnect from the electrical outlet. Hold the plug and press the automatic cord rewind button to rewind the cord automatically. Power button turn the power on or off by pressing lightly downward on the power button ( ). caUtIon: be careful to avoid Power Button injury as cord retracts very quickly. Motorized powerhead Set the power switch on the handle to 1 for rotating brush or 0 to turn rotating brush off. notE: the power brush will automatically turn off if the telescopic tube is in an upright position to protect your carpet from potential damage caused by the rotation of the power brush. notE: the power brush will automatically turn off if the rotator bar is blocked by clogs (hair, cloth, ect. ) for your protection. In that case, turn off the power head, unplug the vacuum, clean the clog, and re-start the power brush. Variable Suction Control PowerBrush On/Off Variable suction power control the variable suction power control is located on the top of the handle. Slide the control toward the larger dots for maximum suction. Slide the control toward the smaller dots to minimize suction for lightly soiled areas or delicate fabrics. caUtIon: before using your vacuum, make sure that the dust bag and all filters (pre-motor and post-motor) are in place. Do not operate your vacuum without the dust bag and filters. 1-800-263-2535 www. bissell. ca 7 Operations Variable height adjustments Step on the brush height adjuster located on the right side of the motorized powerhead to adjust for flooring type (lowest setting (1)for non-carpet, indoor areas, highest setting (6) for plush pile carpet). Handle position Press the handle release pedal, located in the middle of the motorized powerhead, with your foot to place your vacuum into one of the three cleaning positions. Upright­Forstorageandabovefloor cleaningwithtools. normal cleaning­Presshandlerelease pedalonce. Positionusedformosthouseholdfloorcleaningtasks. low cleaning­Withthevacuuminnormal cleaningposition, presshandlereleasepedal again. Useforreachingunderlowfurniture suchastables, chairsorbeds. 3. 2. 3. High filtration dust bag the bISSEll cleanalong features a non-woven, high filtration dust bag that captures more fine dust than traditional paper dust bags, giving off less dust emissions. It also holds more fine dust particles, giving you longer lasting suction power. Tip: Before cleaning under low furniture, check area first for objects that might harm the unit or block the vacuum hose. 8 www. bissell. ca 1-800-263-2535 Operations Bag change indicator the bag change indicator is located between the power button and the automatic cord rewind button. If the bag change indicator turns orange while you are vacuuming, the dust bag needs to be replaced. the dust bag may appear to be full or only partially full depending upon the type of debris picked up. fine particles can block the airflow in the dust bag and reduce suction before the dust bag is full. If the bag change indicator remains orange, even after changing the dust bag, turn the vacuum off and check for a clog in the hose or tools. Dust bag replacement 1. [. . . ] Damage or malfunction caused by negligence, abuse, or use not in accordance with the User's Guide is not covered. limited one year Warranty If your bISSEll product should require service Call BISSELL Consumer Services at the number listed below or visit the BISSELL website ­www. bissell. ca to locate a BISSELL Authorized Service Centre in your area. If there are no authorized BISSELL Service Centres in your area, a BISSELL Representative at canada. custhelp@bissell. ca or at the phone number below will issue you a Return Authorization Number and a pre-paid mailing label to return the unit to BISSELL for warranty repair. The machine should be returned with a photocopy of your proof of purchase. (Your dated sales receipt is your warranty ­ do not send original. ) If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Services. Website: www. bissell. ca E-mail: canada. custhelp@bissell. ca or call: BISSELL Consumer Services 1-800-263-2535 Monday ­ Friday 8 a. m. [. . . ]