User manual BISSELL POWERFORCE 47M6

[. . . ] PowerForceTM BAGLESS USER'S GUIDE 47M6 SERIES 220-240V 3 Safety Instructions 4 Product View 5 Assembly 6-7 Operation 8-12 Maintenance and Care 12-13 Troubleshooting 14 Consumer Services 15 Replacement Parts 16 Warranty ug110_4052_47M6_808. indd 1 8/12/08 1:34:22 PM Thank you for buying a BISSELL PowerForceTM Bagless Vacuum We're glad you purchased a BISSELL PowerForce Bagless Vacuum. Everything we know about floor care went into the design and construction of this powerful, high-tech home vacuuming system. Your BISSELL PowerForce Bagless is well made, and we back it with a limited one year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services Department, so, should you ever have a problem, you'll receive fast, considerate assistance. [. . . ] Always place the vacuum cleaner on the floor with the handle in upright position when using tools. Never place your fingers under the cleaner when it is running. Never place powerfoot on furniture or uneven surfaces. Do not place vacuum cleaner close enough to objects to pull them into rotating brush. NOTICE: certain carpets While vacuuming, and low humidity conditions may generate small static discharges. The discharges are entirely harmless and are not associated in any way with the main power supply. www. bissell. com 7 8/12/08 1:34:28 PM ug110_4052_47M6_808. indd 7 Maintenance and care To maintain maximum cleaning performance from your BISSELL PowerForce Bagless, perform these simple maintenance steps. Empty the dirt container when the dirt reaches the "Full" line on the side. Check the inner and outer circular filters, and the pre-motor filter at least once a month and clean or replace as needed. Clean or replace the post-motor filter every three to six months. Note: More frequent filter cleaning or replacing may be necessary if you are vacuuming new carpet, fine dust, or have allergy concerns. Follow the instructions on the following pages to perform these simple maintenance steps. 3. To reduce the risk of electric shock, turn power switch OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks. WARNING: Tip: For maximum cleaning performance, check and clean or replace all filters as suggested. Emptying dirt container The dirt container needs to be emptied when the dirt reaches the "Full" line on the side of the container. Slide the Lock `n Seal lever to the "Unlock" position. Grasp handle and pull the dirt container straight out to remove from vacuum. Put the dirt container back in the vacuum and slide the lever to the "Lock" position. Note: The dirt container may be washed in warm water with a mild detergent. Remove the filter cup from the bottom before washing. The post-motor filter assists in the filtration process to return clean air to the room. It is located behind the door on the front of the cleaner. When the filter becomes dirty, open the door, remove the filter and clean. The post-motor filter may be hand washed in warm water. Rinse well, then air dry thoroughly before replacing. Replace the door by inserting the tabs on the left side and snapping the right side into place. Post-Motor Filter 3. 4. WARNING: To reduce the risk of injury from moving parts, turn the power switch OFF and disconnect plug from electrical outlet. Check rotating floor brush and drive belt You should check your vacuum cleaner's rotating floor brush and drive belt regularly for wear or damage. You should also clean the brush and brush ends of string, hair and carpet fibers. These can wrap around the brush and hamper its ability to effectively clean your carpet. Also, remove any debris that has accumulated under the brush cover. [. . . ] Check inner and outer circular filter and post-motor filter for correct installation 3. Position correctly and lock into place 4. Remove dirt container and make sure filter cup is fully attached Other maintenance or service not included in the manual should be performed by an authorized service representative. Thank you for selecting a BISSELL product. Please do not return this product to the store. www. bissell. com 13 8/12/08 1:34:36 PM ug110_4052_47M6_808. indd 13 BISSELL Consumer Services If your BISSELL product should require service: In the UK, Australia or New Zealand, call BISSELL Consumer Services at the numbers below and we will give you the location of a BISSELL Authorized Service Center in your area. For all other countries, contact your local in country distributor for questions, service, or repair. [. . . ]