User manual BISSELL SPOTBOT

[. . . ] If your appliance is fitted with a nonrewireable BS 1363 plug it must not be used unless a 13 amp (ASTA approved to BS 1362) fuse is fitted in the carrier contained in the plug. Spares may be obtained from your BISSELL supplier. If for any reason the plug is cut off, it must be disposed of, as it is an electric shock hazard should it be inserted into a 13 amp socket. www. bissell. com 3 Product view Automatic Smart SystemTM Control Panel Front View Clean/Solution Tank Dirty/Collection Tank Flex Hose Clip Vacuum Flex Hose Spray Trigger Tough Stain BrushTM To order replacement parts, additional tools or formulas, please refer to page 15. 4 www. bissell. com Product view Underside View Vacuum Suction Nozzles hands free Cleaning Brush Spray Tip back View Cord Wrap Power Cord Tough Stain TM Brush Storage Hands Free Cleaning Window Keep plenty of genuine bISSEll Advanced Cleaning Formulas on hand so you can clean whenever it fits your schedule. Always use genuine bISSEll deep cleaning formulas. [. . . ] Select which cleaning cycle (surface stain or set-in stain) you would like to begin with. Your SpotBot will begin spraying, brushing and suctioning up the spots and stains in its pre-programmed cycle. Both cycles have been tested and proven to deliver superior cleaning results, taking the guesswork out of cleaning for you. When the cleaning cycle you have selected is complete, the SpotBot will beep. The beep will continue every five seconds until you depress the stop button. Pick up the unit and check the area that was cleaned. If you have used Oxy GEN2, this chemical will continue to work for the next six to eight hours, cleaning your spots and stains all the way to the backing of the carpet. 3. Tip: If the unit accidentally tips or is tilted, the handsfree cleaning brushes will stop. 4. 5. Tip: Some difficult stains may require that you run the cleaning cycle a second time. www. bissell. com 9 Operation Manual/hose cleaning 1. 2. Remove the hose from the unit by depressing the release button. Remove the Tough Stain Brush from the back of the unit by depressing the release button. Attach the Tough Stain Brush onto the grip of the flex hose. Select the manual/hose button on the control panel to start the SpotBot. NOTE: In manual mode, the Spotbot will not turn on until the hose is removed from the unit. If it is not removed within 30 seconds of pushing the start button, the unit will shut off. 1 3. 2a 2b 4. If your unit has a built in heater (not standard on all models) press the heater button to turn on the heat feature. Begin cleaning by holding the tool no more than six inches above the soiled surface. Depress the spray trigger for about five seconds to apply the cleaning solution to the soiled area then release the spray trigger. Using the brush on the tool, gently scrub the soiled area for about 30 seconds or until the soiled area appears to be clean. To suction up the dirt and cleaning solution, position the suction nozzle over the cleaned area, apply downward pressure on the tool, and pull nozzle toward you. You should see the dirty water pass through the nozzle. Continue until no more water can be removed. Normally, this step will require no more than one minute of back and forth passes. NOTE: In manual mode, the Spotbot is equipped with a safety feature which will shut the unit off after 30 minutes. 6. Tip: one of the effective stain removing ingredients in oxy GEN2 is hydrogen Peroxide. Certain people may be affected by the formula when it comes into contact with their skin; it may turn the skin white and/or cause tingling. [. . . ] The Boat Yard 105 Straight Road old Windsor Berkshire, SL4 2SE United Kingdom Telephone: 0844-888-6644 For New Zealand inquiries: monday - friday 9 am -- 5 pm Parex Industries ltd. 5 Tolich Place henderson 0610 Auckland New Zealand Telephone: 0800-247-735 For Australian inquiries: monday - friday 9 am -- 5 pm bISSEll AUSTRAlIA PTY lIMITED 42 Rocco Dr. Scoresby 3179 Victoria Australia Telephone: 1-800-811-183 For all other inquiries: monday - friday 8 am -- 4 pm bISSEll Homecare, Inc. Po Box 1888 Grand Rapids, michigan 49501 USA Telephone: 01-616-453-4451 fax: 01-616-453-1383 bISSEll HOMECARE INC. [. . . ]