User manual BLACK & DECKER BEHTS501

[. . . ] Eu BEHTS301 BEHTS401 BEHTS451 BEHTS501 10 A 10 11 B 7 C D 5 4 E 2 F (Original instructions) ENGLISH G H 8 9 1 I Intended use J Your BLACK+DECKERTM BEHTS301, BEHTS401, BEHTS451, BEHTS501 hedgetrimmers have been designed for trimming hedges, shrubs and brambles. These tools are intended for consumer use only. Safety instructions General power tool safety warnings Warning!Read all safety warnings and all instructions. [. . . ] U Be aware of falling debris when cutting the higher sides of a hedge. U Always hold the tool with both hands and by the handles provided. Residual risks Additional residual risks may arise when using the tool which may not be included in the enclosed safety warnings. These risks can arise from misuse, prolonged use etc. Even with the application of the relevant safety regulations and the implementation of safety devices, certain residual risks can not be avoided. These include: u Injuries caused by touching any rotating/moving parts. U Injuries caused when changing any parts, blades or accessories. u Injuries caused by prolonged use of a tool. When using any tool for prolonged periods ensure you take regular breaks. U Health hazards caused by breathing dust developed when using your tool (example:- working with wood, especially oak, beech and MDF. ) Vibration The declared vibration emission values stated in the technical data and the declaration of conformity have been measured in accordance with a standard test method provided by EN 60745 and may be used for comparing one tool with another. The declared vibration emission value may also be used in a preliminary assessment of exposure. The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used. The vibration level may increase above the level stated. When assessing vibration exposure to determine safety measures required by 2002/44/EC to protect persons regularly using power tools in employment, an estimation of vibration exposure should consider, the actual conditions of use and the way the tool is used, including taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time. Labels on tool The following pictograms are shown on the tool along with the date code: Warning!To reduce the risk of injury, the user must read the instruction manual. 5 ENGLISH (Original instructions) Remove guard retaining screw 10 with a Phillips screwdriver (not supplied). Ensuring the guard slots into the grooves on the unit. U Insert the guard retaining screw 10 into the opening on the side of the guard and tighten securely as shown in Fig. Only use with handle and guard properly assembled to hedge trimmer. The use of the hedge trimmer without the proper guard or handle provided may result in serious personal injury. [. . . ] 65 cm mm s mm kg Level of sound pressure according to EN 60745: Sound pressure level at operator position (LpA) 89 dB(A), uncertainty (K) 3. Technical data BEHTS301 Type 1 Voltage Power input Blade strokes (no load) Blade length Blade gap Blade brake time Saw blade Max cut Weight VAC W min-1 cm mm s mm kg 230 500 1850 50 22 <1 35 2. 65 BEHTS301, BEHTS401, BEHTS451, BEHTS501 – Hedge Trimmer Black & Decker declares that these products described under "technical data" are in compliance with: 2006/42/EC, EN 60745-1:2009 +A11:2010, EN 60745-2-15:2009 +A1:2010 2000/14/EC, Hedge trimmer, Annex V Measured sound power level (LwA) 98 dB(A) Uncertainty (K) 2, 0 dB(A) Guaranteed sound power (LwA) 100 dB(A) These products also comply with Directive 2014/30/EU and 2011/65/EU. For more information, please contact Black & Decker at the following address or refer to the back of the manual. [. . . ]