Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BLACK & DECKER BH35EK. We hope that this BLACK & DECKER BH35EK user guide will be useful to you.
Lastmanuals help download the user guide BLACK & DECKER BH35EK.
Manual abstract: user guide BLACK & DECKER BH35EK
Detailed instructions for use are in the User's Guide.
[. . . ] 8 Wear safety goggles Also use a face or dust mask in case the operations produce dust or flying particles. 9 Beware of maximum sound pressure Take appropriate measures for the protection of hearing if the sound pressure of 85 dB(A) is exceeded. 11 Do not overreach Keep proper footing and balance at all times. 12 Avoid unintentional starting Do not carry the plugged-in tool with a finger on the switch. [. . . ] 1 2 3 4 5 6 Variable speed switch Tool holder for SDS-plus® accessories Mode selector with safety lock Side handle Depth adjustment rod Depth stop clamp Torque limiting clutch All rotary hammer drills are equipped with a torque limiting clutch that reduces the maximum torque reaction transmitted to the operator in case of jamming of a drill bit. This feature also prevents the gearing and electric motor from stalling. the torque limiting clutch has been factory-set and cannot be adjusted. Variable speed The variable speed feature allows speed to build up slowly, thus preventing the drill bit from walking off the intended hole position when starting. Always check that the power supply corresponds to the voltage on the rating plate. Your Elu tool is double insulated in accordance with EN 50144; therefore no earth wire is required. Check for damage to the tool, parts or accessories which may have occurred during transport. Take the time to thoroughly read and understand this manual prior to operation. Should your mains plug need replacing and you are competent to do this, proceed as instructed below. If you are in doubt, contact an Elu authorized repair agent or a qualified electrician. Cut off the plug and dispose of it safely; a plug with bared copper conductors is dangerous if engaged in a live socket outlet. Only fit 13 Amperes BS1363A approved plugs fitted with the correctly rated fuse (1). The cable wire colours, or a letter, will be marked at the connection points of most good quality plugs. Your Elu heavy duty rotary hammer drill BH35EK has been designed for professional rotary drilling and hammer drilling as well as light chipping, chiselling and demolition applications and for carbide-tipped core drilling. Before replacing the top cover of the mains plug ensure that the cable restraint (3) is holding the outer sheath of the cable firmly and that the two leads are correctly fixed at the terminal screws. B) The rotary hammer drill can be used in three operating modes: Rotary drilling: for drilling into metal, wood and plastics Hammer drilling: simultaneous rotating and impacting for concrete and masonry drilling and carbide-tipped core drilling Hammering only with spindle lock: impacting only - for light chipping and chiselling Bit rotation: non-working position used only to rotate a flat chisel into the desired position. Select the required operating mode by depressing the safety lock (8) and rotating the mode selector (3) towards the symbol on the housing until the safety lock clicks into position. Do not select the operating mode when the tool is running. Turn the bit slightly whilst depressing the accessory, until it clicks into position. The hammering function requires the bit to be able to move axially several centimetres when locked in the tool holder. To remove an accessory, pull back the tool holder locking sleeve (9) and pull out the bit. Never connect the live (L) or neutral (N) wires to the earth pin marked E or . [. . . ] If your Elu product becomes defective due to faulty materials or workmanship within 12 months from the date of purchase, we guarantee to replace all defective parts free of charge or, at our discretion, replace the unit free of charge provided that: · Cleaning Keep the ventilation slots clear and regularly clean the housing with a soft cloth. Unwanted tools and the environment Take your tool to an Elu authorized repair agent where it will be disposed of in an environmentally safe way. All Elu Power Tools are thoroughly tested before leaving the factory. However, if the Power Tool needs repair, please contact your dealer or the Elu Head Office for the address of the nearest Elu authorized repair agent (please refer to the back of this manual). [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BLACK & DECKER BH35EK
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual BLACK & DECKER BH35EK will begin.