User manual BLACK & DECKER KS801SEKA

[. . . ] 2 6 1 Cu on eC rv ol tr ™ 3 5 4 www. blackanddecker. eu KS801SE KS901PE KS901SE 7 8 3 5 A B 11 C 6 1 2 10 D 12 6 12 0 PVC 3 E 2 KS901PE F KS801SE KS901SE 13 15 4 G H 14 16 I K J 3 ENGLISH (Original instructions) 3. Personal safety a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. [. . . ] The vibration level may increase above the level stated. When assessing vibration exposure to determine safety measures required by 2002/44/EC to protect persons regularly using power tools in employment, an estimation of vibration exposure should consider, the actual conditions of use and the way the tool is used, including taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time. Labels on tool The following symbols are shown on the tool: : Warning!To reduce the risk of injury, the user must read the instruction manual. 5 ENGLISH Electrical safety (Original instructions) # Use Adjusting the shoe plate for bevel cuts (fig. Never use the tool when the shoe plate is loose or removed. The shoe plate (4) can be set to a left or right bevel angle of 22. 5° or 45°. u Pull the shoe (4) forward, rotate the shoe to the left or right and push it back into the 22. 5° or 45° location. To reset the shoe plate (4) for 90° cuts: u Loosen the screw (10). u Pull the shoe (4) forward, rotate to the centre and push it back into the 0° location. u Tighten the screw. This tool is double insulated; therefore no earth wire is required. Always check that the power supply voltage corresponds to the voltage on the rating plate. u If the supply cord is damaged, it must be replaced by the manufacturer or an authorised BLACK+DECKER Service Centre in order to avoid a hazard. Features This tool includes some or all of the following features. 1. Variable speed switch (KS901PE) or On/Off switch (KS801SE and KS901SE) 2. Lock-on button 3. Saw blade locking lever 4. Shoe plate 5. Dust extraction outlet 6. Pendulum stroke / AutoSelect dial Variable speed control u Assembly Warning!Before attempting any of the following operations, make sure that the tool is switched off and unplugged and that the saw blade has stopped. Used saw blades may be hot. Use a high speed for wood, medium speed for aluminium and PVC and low speed for metals other than aluminium. Switching on and off u Fitting the saw blade (fig. A) u Hold the saw blade (7) as shown, with the teeth facing forward. u Push the locking lever (3) away from the shoe plate (4). u Insert the shank of the saw blade into the blade holder (8) as far as it will go. Slide the vacuum nozzle into the dust extration outlet (5). To switch the tool on, press the variable speed switch (1). On KS901PE units the speed depends on how far you depress the switch. u For continuous operation, press the lock-on button (2) and press the variable speed switch. This option is available only at full speed. u To switch the tool off, release the variable speed switch. To switch the tool off, when in continuous operation, press the variable speed switch once more and release it. Connecting a vacuum cleaner to the tool (fig. [. . . ] u Using rip fence as a pivot arm, begin cutting circle. Should you find one day that your BLACK+DECKER product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection. Z z Separate collection. This product must not be disposed of with normal household waste. Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials. Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product. [. . . ]