User manual BLAUPUNKT ALICANTE CD32

[. . . ] Radio / CD Alicante CD32, Kiel CD32 Porto CD32 San Remo CD32 Santa Cruz CD32 Operating instructions http://www. blaupunkt. com Bitte aufklappen Open here Ouvrir s. v. p. Öppna Por favor, abrir Favor abrir Åbn her 2 1 12 2 11 3 4 10 5 9 8 6 7 3 SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH DEUTSCH DANSK PORTUGUÊS ESPAÑOL CONTROLS DEUTSCH DANSK PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH 1 2 3 4 5 6 7 button to release the control panel. Long press: Button, to switch the unit on/off, Short press: To mute the unit's volume. Short press: SRC button, to select the CD, radio, CD changer or Compact Drive MP3 (if connected) and AUX sources. [. . . ] When you have finished making your changes, Set the mute level using the must be connected to the car radio in the manner described in the installation instructions. You can find out from your Blaupunkt dealer which navigation systems can be used with your car radio. If a traffic information message is received during a telephone call or whilst a navigation announcement is being made, the traffic message will only be played after the call or voice output is finished. If you are already listening to a traffic announcement and a telephone call arrives or the navigation system wishes to make a voice output, the traffic announcement will first be heard. Once the traffic message is finished, you can listen to the call or the voice output. You can set the volume level at which telephone calls and the navigation voice output will first be heard. Press the MENU button 7. Keep pressing the or button 5 until "TEL VOL" appears in the display. press the MENU button 7 twice. REG: At certain times, some radio stations divide their programme into regional programmes providing different regional content. You can use the REG function to prevent the car radio from switching to alternative frequencies that are transmitting different programme content. Note: REG must be separately activated/ deactivated in the menu. Press the MENU button 7. Keep pressing the or button 5 until "BEEP" appears in the display. Use the and buttons 5 to switch between the options. "OFF" means beep off, "ON" means the beep is switched on. Press the MENU button 7. 32 RADIO MODE Press the MENU button 7. Keep pressing the or button 5 until "REG" appears in the display. "OFF" or "ON" is displayed alongside "REG". To switch REG on/off, DEUTSCH DANSK PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH Switching REG on/off Selecting the memory bank To switch between the FM memory banks and the MW and LW wavebands, keep pressing the BND·TS button < until the required waveband / memory bank is displayed. Tuning into a station There are various ways of tuning into a station. Automatic seek tuning press the or button 5. Press the MENU button 7. Switching the RDS function on/off To use the RDS functions (AF and REG), press the TRAF·RDS button ; for longer than two seconds. The RDS functions are active when RDS lights up in the display. Press the or button 9. The unit tunes into the next receivable station. Setting the sensitivity station seek tuning You can configure the radio to only tune into stations with a strong reception or to also tune into those with a weak reception. Keep pressing the or button 5 until "SENS" appears in the display. The display shows the currently set value for sensitivity. "SENS HI6" means that the tuner is highly sensitive. "SENS LO1" means it is set to the lowest sensitivity setting. [. . . ] When you have finished making your changes, press the AUDIO button 9. Adjusting the fader settings To adjust the front/back volume distribution (fader), press the AUDIO button 9. Adjusting the treble settings To adjust the TREBLE, press the AUDIO button 9. "BASS" appears in the display. press the AUDIO button 9. "BASS" appears in the display. Keep pressing the Keep pressing the or button 5 until "TREB" appears in the display. or button 5 until "FADER" appears in the display. Press the or button 5 to adjust the treble. When you have finished making your changes, Press the or button 5 to adjust the fader (front/back). [. . . ]