User manual BLAUPUNKT ALICANTE CD34

[. . . ] Radio / CD Alicante CD34 Freiburg CD34 Operating instructions 7 644 172 310 7 644 194 310 http://www. blaupunkt. com Open here 2 1 2 3 11 4 5 10 6 7 9 8 3 SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH DEUTSCH DANSK PORTUGUÊS ESPAÑOL CONTROLS 1 button for opening the detachable control panel (flip-release panel) Button to switch the device on/ off and operate the volume mute feature BND button (band) to select radio mode as the source, to select the FM memory banks and the MW and LW wavebands TS to start the Travelstore function Volume control TRAF button to switch traffic information standby on/off. RDS button to switch the RDS function on/off (Radio Data System). 6 AUDIO button to adjust the bass, treble, balance and fader. For adjusting the X-BASS function and activating/deactivating it. [. . . ] Automatic station seek tuning Press the or button 8. The radio tunes into the next receivable station. Tuning into stations manually You can also tune into stations manually. Note: You can only tune into stations manually if the RDS function is deactivated. Press the or button 8. Selecting the waveband / memory bank This device can receive programmes broadcast over the FM frequency range as well as the MW and LW (AM) wavebands. There are three memory banks available for the FM waveband (FM1, FM2 and FMT) and one for each of the MW and LW wavebands. Six stations can be stored in each memory bank. To switch between the FM memory banks (FM1, FM2 and FMT) and the MW and LW wavebands, briefly press the BND·TS button 3. 36 Browsing through broadcasting networks (only FM) If a radio station provides several programmes, you have the option of browsing through its so-called "broadcasting network". Note: The RDS function must be activated before you can use this feature. Press the or button 8 to switch to the next station on the broadcasting network. Note: When using this feature, you will only be able to switch to stations that you have received once before already. To receive the stations, use the Scan or Travelstore function. RADIO MODE DEUTSCH DANSK PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH Setting the sensitivity of station seek tuning You can choose whether the radio should only tune into stations providing good reception or whether it can also tune into those with a weak reception. Storing stations automatically (Travelstore) You can automatically store the six stations providing the best reception in the region (only FM). The stations are stored in the FMT memory bank. Note: Any stations that were previously stored in this memory bank are deleted in the process. Press the MENU button 9. Press the or button 8 repeatedly until "SENS" appears in the display. Press the button 8. Press and hold down the BND·TS button 3 for longer than two seconds. "FM TSTORE" appears in the display. After the process has completed, the radio will play the station that is stored in memory location 1 of the FMT memory bank. The display shows the currently set sensitivity level. "SENS HI6" means that the tuner is set to the highest sensitivity setting. "SENS LO1" means it is set to the lowest sensitivity setting. Set the sensitivity level that you buttons 8. want using the When you have finished making your changes, press the MENU button 9. Note: You can set different sensitivity levels for FM and MW or LW (AM). Listening to stored stations Select the memory bank or waveband. Press the station button 1 - 6 : that corresponds to the station that you want to listen to. Storing stations Storing stations manually Scanning receivable stations (SCAN) You can use the scan function to briefly play all the receivable stations. You can set the scanning time in the menu to between 5 and 30 seconds. Starting SCAN Select the memory bank (i. e. FM1, FM2, FMT) that you want or one of the wavebands (MW or LW). Tune into the station that you want. Press and hold down one of the station buttons 1 - 6 : for longer than two seconds to assign the station to that button. Press and hold down the MENU button 9 for longer than two seconds. "SCAN" appears briefly in the display followed by a flashing display of the current station name or frequency. [. . . ] Adjusting the treble Press the AUDIO button 6. "BASS" appears in the display. Press the button 8 repeatedly until "FADER" appears in the display. Press the Press the button 8 repeatedly until "TREB" appears in the display. or button 8 to adjust the treble. When you have finished making your changes, or button 8 to adjust the fader (front/back). When you have finished making your changes, Press the press the AUDIO button 6. press the AUDIO button 6. 47 SOUND Equalizer presets This device is equipped with an equalizer that has been preset with settings for the "ROCK", "POP" and "CLASSIC" music styles. To select an equalizer preset, X-BASS X-BASS The X-BASS feature can be used to boost the bass at low volume levels. [. . . ]