User manual BLAUPUNKT BREMEN RCM 127

[. . . ] Radio / Cassette Bremen RCM 127 Operating instructions Table of contents Traffic safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Quick reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 KeyCard - Anti-theft system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Switch the warning beep off as described above. Adjusting the volume for traffic announcements This volume was preset at the factory, though you can alter the value using the DSC function (see "Programming with DSC ­ TUNER, TA VOL"). Adjusting the sound stage for traffic messages and TIM You can adjust the treble, bass, balance and fader settings separately for both traffic announcements and TIM. It is, for example, possible to have only the front left (or right) speaker transmit the traffic messages. This provides the driver with the important traffic information without unnecessarily bothering the passengers in the vehicle. To alter the setting: During an announcement · press S briefly. · · Select the settings you wish to adjust by pressing the corresponding key, e. g. treble. S Press << / >> or / to adjust the sound as you wish to hear it for future traffic messages. The last setting made will be stored automatically. 8 seconds after the last setting is made, the unit will switch back to the previous menu. You can return to the previous menu immediately by · pressing EXIT . TIME TREBLE BASS FADER BALANCE 12:13 EXIT 31 DEUTSCH ENGLISH FRANÇAIS ITALIANO NEDERLANDS SVENSKA ESPAÑOL CD - Betrieb (Option) PORTUGUÊS Traffic Memo (TIM) This set is equipped with a digital speech memory which can automatically record up to four traffic messages lasting a maximum of four minutes. As soon as TP appears in the display, the system will record all incoming traffic messages broadcast by the station when the radio is switched on. If the priority for traffic announcements is activated (TA shown in the display panel), the set will also record the messages broadcast by the traffic station of the same programme network (see also "Traffic message reception with RDSEON"). If "TIM ACTIVE" appears briefly in the display when the radio is switched off, the TIM standby mode is active. In this case the radio will record the traffic information broadcast for 90 minutes before and after the programmed TIM times even if it is switched off. The radio will also record the traffic messages broadcast by the last station it was tuned into for three hours after the set has been switched off. Depending on the length of the new message, the oldest messages will be deleted automatically. If a message is longer than four minutes, "OVERFLOW" will appear in the display header for 2 seconds after you have activated TIM to indicate that the system was unable to record the message in full. S TIM ACTIVE Warning Your motor antenna may be damaged in a car wash If your vehicle is equipped with a motor antenna, then please be sure to read the important warning note at the end of this section. 32 Setting the exact time TIM needs the exact time in order to operate precisely. Note that the clock also has to be reset after any interruption in the power supply. If the time display is highlighted there has been an interruption in the power supply. When you switch the radio on, the FIRST INSTALL menu will appear automatically. Setting the clock following an interruption in the power supply · Press CLOCK and the time will be appear in the display header. To set the clock · alter the hours by pressing - HOURS / HOURS + and the minutes by pressing - MIN / MIN + . When you have completed resetting the clock · press EXIT . [. . . ] The car radio's lighting connector must be hooked up to the vehicle's electric system for this to function properly. Select whether the characters in the display should appear positively or negatively. ALWAYS POSITIVE The characters will always appear positively. ALWAYS NEGATIVE The characters will always appear negatively. S DSC-MAIN MENU TUNER CD CLEAR DISPLAY VARIOUS EXIT KEYCARD DISPLAY COLOUR ANGLE BRIGHT S DSC-DISPLAY MENU COLOUR ANGLE BRIGHT POS/NEG EXIT MENU-OFF POS/NEG 63 DEUTSCH ENGLISH FRANÇAIS ITALIANO NEDERLANDS SVENSKA ESPAÑOL CD - Betrieb (Option) PORTUGUÊS AUTO POS/NEG Automatic switch. [. . . ]