User manual BLAUPUNKT BRISTOL CD36

[. . . ] Radio CD Bristol CD36 Vancouver CD36 7 646 075 310 7 646 067 310 Operating instructions http://www. blaupunkt. com 1 2 3 4 5 6 7 13 12 11 10 9 8 2 CONTROLS 1 Button to switch the device on/ off and operate the volume mute function. button for detaching the control panel (release panel). Volume control CD compartment AUDIO button to adjust the bass, treble, balance and fader. MENU button Short press: Open the settings menu. [. . . ] or button 8. Press the Press the MENU button 7. Selecting the waveband / memory bank You can use this device to receive programmes broadcast over the FM frequency range as well as the MW and LW (AM) wavebands. There are three memory banks available for the FM waveband (FM1, FM2 and FMT) and one for each of the MW and LW wavebands. Six stations can be stored in each memory bank. To switch between the FM memory banks (FM1, FM2 and FMT) and the MW and LW wavebands, Browsing through broadcasting networks (only FM) If radio stations provide several programmes, you have the option of browsing through their "broadcasting networks". Note: G The RDS function must be activated before you can use this feature. Press the or button 8 to switch to the next station on the broadcasting network. briefly press the BND·TS button <. Note: G When using this feature, you will only be able to switch to stations that you have received once before already. To receive the stations, use the scan function or the Travelstore function. 34 RADIO MODE DEUTSCH DANSK PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH Setting the sensitivity of station seek tuning You can choose whether the radio should only tune into stations providing good reception or whether it can also tune into those with a weak reception. Press the or button 8 repeatedly until "SENS" and the currently set value appear in the display. "SENS HI6" means that the tuner is set to the highest sensitivity setting. "SENS LO1" means it is set to the lowest sensitivity setting. Set the desired sensitivity using the buttons 8. When you have finished adjusting the setting, press the MENU button 7. Note: G You can set different sensitivity levels for FM and MW or LW (AM). Storing stations automatically (Travelstore) You can automatically store the six stations providing the best reception in the region (only FM). The stations are stored in the FMT memory bank. Note: G Any stations previously stored in this memory bank are deleted in the process. Press and hold down the BND·TS button < for longer than two seconds. "FM TSTORE" appears in the display. After the process has completed, the radio will play the station that is stored in memory location 1 of the FMT memory bank. Listening to stored stations Select the memory bank or waveband. Press the station button 1 - 6 ; that corresponds to the station that you want to listen to. Storing stations Storing stations manually Select the memory bank that you want (FM1, FM2, FMT) or one of the wavebands (MW or LW). Press and hold down one of the station buttons 1 - 6 ; for longer than two seconds to assign the station to that button. Scanning receivable stations (SCAN) You can use the scan function to listen to all the receivable stations briefly. You can set the scanning time in the menu to between 5 and 30 seconds (in steps of 5 seconds). Starting SCAN Press and hold down the MENU button 7 for longer than two seconds. "SCAN" appears briefly in the display followed by a flashing display of the current station name or frequency. [. . . ] When you are not changing any settings, the level display depicts the peak music/speech output. You can switch the level display on/off. Press the MENU button 7. "MENU" appears in the display. Press the X-BASS button 9. Press the or button 8 repeatedly until the setting that you want appears in the display. When you have finished adjusting the setting, Press the Press the or button 8 repeatedly until "PEAK LVL" appears in the display. press the X-BASS button 9. or button 8 to switch between "PEAK ON" and "PEAK OFF". [. . . ]