User manual BLAUPUNKT CDC A01

[. . . ] You can read the terms and conditions of guarantee on the Internet at www. blaupunkt. de or request them directly by writing to: Blaupunkt GmbH Hotline CM/PSS 6 Robert Bosch Str. 200 D-31139 Hildesheim, Germany Before Installing the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . 4 Transport Locking Screws . . . . . . . . . . . . . . . 4 Precautions for Installation and Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Make certain to remove these screws before installing the changer. Precautions for Installation and Wiring 1. Do not install the equipment in the following locations: - Locations that are exposed to direct sunlight. - Locations at which warm air exits the car heating system. - Locations in which proper installation is impossible and locations in which many vibrations are produced. Note: After removing the transport locking screws, place the enclosed seals over the screw holes. These seals prevent dust from entering the device, which could lead to malfunctions. 2. - Make certain to use the brackets and screws supplied. - When installing the equipment, do not use any screws that are part of the braking or steering systems. The device may only be installed in the approved manner (on one of its sides, on one of its ends, at an angle of 45°, or suspended. If it is installed upside-down or with the front facing down, malfunctions may occur. 4 BEFORE INSTALLING THE EQUIPMENT ENGLISH PORTUGUÊS ESPAÑOL FRANÇAIS Position of the Built-in AntiVibration Armature This device can be installed horizontally (suspended), vertically, or at a 45° angle. Once you have chosen an installation procedure, you have to set the position of the built-in anti-vibration armature accordingly. Please do this before carrying out the procedures explained below. Vibration may cause CDs to skip if the equipment is used before the antivibration system has been configured correctly. - The anti-vibration armature is set to "0" (for horizontal installation) at the factory before shipping. - The built-in anti-vibration armature adjusts on both the left and right sides. - Before attaching the brackets, use a screwdriver to set the position of the anti-vibration armature. For horizontal or suspended installation: Make certain that the built-in anti-vibration armature is set to the "0" position. 5 BEFORE INSTALLING THE EQUIPMENT For vertical installation: The built-in anti-vibration armature should be set to the "90" position. USING THE CHANGER Using the Changer Loading a CD 1. Press the button on the CD drawer of the magazine and slide out only one drawer. For installation at a 45° angle: The built-in anti-vibration armature should be set to the "45" position. 2. Insert the CD in the drawer with the playable side down (in other words, with the label facing up). Each drawer can only hold one CD. Printed side faces up Playable side faces down 3. Press the button on the CD drawer so that it closes by sliding inside the magazine. 6 USING THE CHANGER You can load up to ten CDs. ENGLISH To eject the magazine: Installing the Magazine 1. Slide the cover to the right. Eject button 2. First make certain that the magazine is oriented so that the CD labels face up and so that the magazine faces in the proper direction for installation. [. . . ] Do this using the hex bolts (M6 x 12) and hex nuts (M6). 2. Position of the built-in antivibration armature Hex bolts (M6x12) 3. - Unscrew the hex nuts and remove the CD changer. Hex bolts (M4x5) 11 INSTALLATION 4. - Using a knife, cut through the carpet directly above the bolts of the mounting bracket (B). - Replace the carpet in its original position, so that the bolts poke through the carpet. Installation Procedure for Installation on Carpet (Vertical Position) 1. - Make certain that the built-in anti-vibration armature has been set to the "90" vertical installation position on both the right and left sides. - Using the hex bolts (M4 x 5), fasten the left and right brackets (A). - Fasten the left and right brackets (A) to the corresponding brackets (B). [. . . ]