User manual BLAUPUNKT GTA 250 BP11 INSTALLATION

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BLAUPUNKT GTA 250 BP11. We hope that this BLAUPUNKT GTA 250 BP11 user guide will be useful to you.

Lastmanuals help download the user guide BLAUPUNKT GTA 250 BP11.


Mode d'emploi BLAUPUNKT GTA 250 BP11
Download
Manual abstract: user guide BLAUPUNKT GTA 250 BP11INSTALLATION

Detailed instructions for use are in the User's Guide.

[. . . ] For devices purchased outside the European Union, the warranty terms issued by our respective responsible domestic agency are valid. The warranty terms can be called up from www. Please observe the following safety notes during the installation and connection. ­ When you drill holes, ensure that you do not damage any vehicle components. [. . . ] Stereo Mode Max power Mono mode Max power Stereo Mode Max power Stereo Mode RMS power Mono mode RMS power Stereo Mode RMS power Frequency response Signal-to-noise ratio Signal-to-noise ratio Distortion factor (RMS) Stability Input sensitivity 2 x 110 W / 4 1 x 330 W / 4 2 x 160 W / 2 2 x 55 W / 4 1 x 165 W / 4 2 x 80 W / 2 10 Hz - 30, 000 Hz > 85 dB @ RMS power > 75 dB @ 1 W / 1 kHz < 0. The performance of an amplifier can only be as good as its installation. A correct installation increases the overall performance of your car sound system. the GTA amplifier should be installed by a trained person. If you would to install it yourself, please read these installation instructions very carefully and allow yourself sufficient time for the installation. In conclusion, allow us a few words about the topic of health protection: During the playback of music in your vehicle, please consider that continuous sound-pressure levels above 100 dB can lead to permanent damages to the human ear and even to loss of hearing. Using today's high-performance systems and loudspeaker configurations allows for reaching soundpressure levels above 130 dB. Please observe the following safety notes during the installation and connection. ­ When you drill holes, ensure that you do not damage any vehicle components. ­ The cross section of the plus and minus cable may not be less than 6 mm2. Use cable glands for holes with sharp edges. ­ An incorrect installation can result in malfunctions of the electronic vehicle systems or your car sound system. You can select between 2 different audio inputs; ­ Cinch (RCA) ­ Hi level (loudspeaker connections) Use only one of the audio inputs; otherwise, it may lead to audio interferences. The preamplifier outputs are connected to the cinch (RCA) sockets 1 via a shielded sound cable. with control via the loudspeaker outputs , the input connections of pos. 2/3 are fed to the closest loudspeaker cables (front or rear) on the left and right. Bridge output stages (BTL) can also be connected directly without an additional adapter. With respect to accident safety, the GTA 250 BP11 must be secured in a professional way. When selecting the installation location, select a dry location that offers sufficient air circulation for cooling the amplifier. The GTA 250 BP11 must not be installed on rear shelves, rear seats or other locations that are open to the front. The installation location must be suitable to accept the accompanying screws and provide a firm support. ­ Securely fasten commercially available minus cables to a noise-free earth point (chassis screw, chassis metal) (not to the minus pole of the battery). [. . . ] This allows the amplifier to be switched on and off using the on/off-switch of the radio device. The Level control is used to adjust the input sensitivity of the power amplifier to the output voltage of your car sound system preamplifier output. If a car sound system of a third party manufacturer is connected, the input sensitivity must be adjusted corresponding to the manufacturer data. A few important explanations in this context: By turning the control clockwise, the input sensitivity of the amplifier and, therefore, also the volume increases. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BLAUPUNKT GTA 250 BP11

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual BLAUPUNKT GTA 250 BP11 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag