User manual BLAUPUNKT GTP 01 PORT. MP3 PLAYER

[. . . ] UP button, to adjust the volume, treble and bass. DOWN button, to adjust the volume, treble and bass. Battery compartment cover. CONTENTS Inserting batteries . . . . . . . . . . . . . . . . . . 14 Switching on/off . . . . . . . . . . . . . . . . . . . . [. . . ] You will find the hotline telephone numbers printed at the back of this booklet. The GTP 01-MP3 is an MP3 player that plays MP3 music files saved on MultiMedia Cards (MMC). MMCs (possible sizes: 8/16/32/64 MB) are not included. MP3 is a process developed by the Fraunhofer Institute for compressing CD audio files. Compression allows data to be reduced to around 15% of their original size without a noticeable loss in quality (at a bitrate of 192 Kbit/s). If a lower bitrate is used to convert CD audio data to MP3, you can create smaller files but there will be a loss of quality. OPERATION The GTP 01-MP3 runs on two AAA-size 1. 5 V batteries (not included). To open the battery compartment on the back of the GTP 01-MP3, DEUTSCH PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH Inserting batteries È gently press the arrow symbol on the battery compartment cover ?and slide it towards the top end of the unit. È insert two AAA-size 1. 5 V batteries as indicated by the symbols in the battery compartment. È slide the battery compartment cover from the top of the unit into the guide until it clicks into place. Note: To avoid damaging the GTP 01-MP3, please observe the following: q Always replace both batteries at the same time. q Remove the batteries if you are not using the GTP 01-MP3 for a longer period of time. q Remove the batteries as soon as they are drained. q Battery fluid escaping from totally discharged batteries is damaging to health and the environment. Environmental advice: q Please take discharged batteries to a collection point where they will be disposed of properly. Old batteries do not belong in your household refuse bin. 13 OPERATION Connecting headphones A pair of stereo headphones is supplied with the unit. Adjusting the volume You can adjust the volume from 0 to 30. To increase the volume, È Connect the headphones by carefully inserting the headphone plug into the headphone jack 3 until it reaches its end position. È press the UP button =. To decrease the volume, È press the DOWN button >. Switching on/off È To switch the unit on, press button 1. Playback begins with the first track on the MMC. Inserting/removing an MMC To avoid damaging the MMC, you should only change the MMC whilst the unit is switched off. To insert an MMC, È hold the MMC with its printed side uppermost and gently slide it (whilst keeping it straight) into the MMC slot 8 until it reaches its end position. To remove an MMC, È hold the MMC by your fingertips and pull it straight out of the MMC slot 8. È To switch the unit off, press button 1 for longer than two seconds. The unit switches off. Securing the unit (HOLD) You can prevent the unit's controls from accidentally being operated, e. g. To activate the HOLD function, È press the HOLD button 2 for longer than two seconds. If you now press a button, , , HOLD" will appear in the display. If you want to operate the unit again, you must first deactivate the HOLD function. [. . . ] The current track continues to play for another 10 seconds. Afterwards, all the tracks will be intro-scanned for 10 seconds in ascending order until you cancel the INTRO function. 15 OPERATION INTRO function, continuing listening to a track If you want to continue listening to a track on the MMC that is currently being intro-scanned, È press the SEL : button if you want to adjust the bass. The settings are saved. Adjusting the bass To optimise the sound, you can set the bass to a value between ­9 and +9. È press the INT button 6. , , INT" disappears from the display. È Press the SEL button : three times. , , BASS" and the value that is set appear in the display. Pausing playback (PAUSE) If you want to pause playback, È press button 7. , , PAUSE" appears in the display. È Press the UP = or DOWN > button to increase/decrease the value. [. . . ]