User manual BLAUPUNKT HONOLULU CD50 RED US

[. . . ] 6 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 International telephone information . . . 6 ENGLISH PORTUGUÊS ESPAÑOL FRANÇAIS Important information . . . . . . . . . . . . . . [. . . ] Never leave the release panel in the car, even if it is well hidden. The panel has been designed so that it is easy to remove. Do not expose the release panel to direct sunlight or other heat sources. Store the release panel in the case supplied. guides from left to right. Press the left-hand side of the panel onto the car audio system until it locks into place. Removing the operating panel Press 1. The release panel will unlock. 1 Note: While replacing the panel, be careful not to press on the display. If the car audio system was on when you removed the panel, it will automatically switch back on using the same settings when you replace it (radio, CD player or CD changer). First pull the operating panel forward and then slide it to the left to remove it. 7 PORTUGUÊS ESPAÑOL Replacing the operating panel Slide the operating panel into the FRANÇAIS ENGLISH Removable front panel When you remove the operating panel, the car audio system will automatically switch off. A CD inserted into the car audio system will remain in place. SWITCHING ON/OFF Switching the car audio system on/off The car audio system can be switched on/off in a number of ways. Switching the car audio system on/ off with the ignition If the car audio system has been connected to your vehicle ignition, it is possible to switch it on and off with the ignition. You can also switch the car audio system on when the ignition is switched off. Switching the car audio system on by inserting a CD If the system is switched off and there is no CD in the CD player, press 9. The flip release panel will open. Insert the CD into the CD player with the label facing upwards until you feel resistance. The CD will be pulled automatically into the CD player. Do not attempt to assist or prevent this process. Press down and hold 3 until the car audio system switches on. "0" means the beep volume is off, "9" means the beep volume is adjusted to the maximum volume. Once you have adjusted the settings, press MENU 8 or OK ;. To switch between the different FM memory banks , press FM 4. To select the AM waveband, press AM 5. Tuning into radio stations You can tune into radio stations in a number of different ways. Automatic seek tuning Press or :. The radio will tune into the next available station within reception range. Manual station selection You can also tune into radio stations manually. Press or :. 10 RADIO OPERATION It is also possible to adjust the sensitivity of the seek tuning function to tune the radio into stations with strong reception signals only, or to those with weaker reception signals as well. ENGLISH PORTUGUÊS ESPAÑOL FRANÇAIS Adjusting seek tuning sensitivity Storing radio stations automatically (Travelstore) You can automatically store the six radio stations with the strongest reception in your current reception area. These stations will be stored in the FMT or AM memory bank depending on the selected waveband. Note: Any stations stored previously in the memory bank will be deleted. Press MENU 8. Press : repeatedly until "SENS" appears in the display. Press :. The currently selected setting will appear in the display. "SENS HI" indicates the highest level of sensitivity, "SENS LO" the lowest. If you select "SENS LO", "lo" will light up in the display. Press TS ?briefly. The storing process will begin. "TRAVEL-STORE" will appear in the display. After the stations have been stored, the radio will automatically begin to play the station stored on preset button 1 of the respective memory bank. Press sensitivity. : to adjust the desired Once you have made your selection, press MENU 8 or OK ;. Storing radio stations Storing radio stations manually Recalling stored radio stations Select the desired station memory bank. Press the station button 1 to 6 > on which you have stored the desired radio station. Select the desired memory bank FM1, FM2 or FMT or the waveband AM. Tune the radio into the desired station. Scanning the radio stations within reception range (SCAN) You can scan all of the radio stations currently within your reception range. [. . . ] The hours will begin to flash. Press hours. or : to alter the press / DIS 7. Once you have set the time, press MENU 8 or OK ; twice. The time will then appear in the display for eight seconds. Selecting the 12/24-hour time display mode Press MENU 8. "MENU" will appear in the display. Press : repeatedly until "24 H MODE" or "12 H MODE" appears in the display. : to switch the dis- Press or play mode. Once you have selected the mode, press MENU 8 or OK ;. 16 TONE AND BALANCE/FADER Loudness boosts the bass and treble when the volume is low to create a more natural sound. ENGLISH PORTUGUÊS ESPAÑOL FRANÇAIS Adjusting the tone and balance/fader Adjusting the bass To adjust the bass, press AUD / LD =. "BASS" will appear in the display. Switching Loudness on/off Press AUD / LD = for approx. [. . . ]