User manual BLAUPUNKT IVMR 1042P

[. . . ] 13 Changing the battery in the remote control . 14 English 2 MONITOR OVERVIEW (IVMR-7002P Shown) 1 2 3 4 1 11 12 13 5 10 * 14 7 6 8 9 *Note: Buttons 6-9 are located on the right side of the display screen on Model IVMR-1042P. [. . . ] · Do not attempt to open or dismantle the monitor, since you could suffer an electric shock as a result. · Avoid using the monitor in environments where it is subjected to dust, dirt or moisture. 6 SUPPLIED PARTS The monitor is supplied with all the parts listed below. Please check that the range of parts supplied with your device is complete. If one of the listed parts is missing, please contact your dealer immediately. · Monitor (including mounting plate and screws) · Remote control IVRC-06 with battery · 5 m long, 13-pin extension cable · Connection adapter (13-pin RCA/jack) · Operating instructions 7 INSTALLING THE MONITOR Installing the monitor (mechanical) Select a suitable position for secure installation of the monitor: · The device must not distract the driver or restrict the driver's view. · The ability to enter and get out of the vehicle must not be impeded. · The device must not be installed in such a way that could prevent the other vehicle components from functioning properly (e. g. · Make sure that the device is installed in a safe and secure position and that it cannot become detached in the event of an emergency stop. · Do not attach the device merely to the roof liner. · If you need to drill additional holes, make sure you do not drill through the sheet metal of the vehicle's roof. · Avoid using the monitor over a longer period of time while the engine is off in order to prevent the battery from becoming discharged. Screws for securing the ceiling-mounted monitor Screws for securing the mounting plate English 8 INSTALLING THE MONITOR Cables 11 12 Interior lighting connection (3 wires) Red wire = Constant +12V White wire = To the door switch (Negative Door Trigger) Black wire = Ground Warning notice: The operating voltage cable must be protected with at least a 1. 5 A fuse. Extension cable (13 pin) Adapter cable Monitor connection (13 pin) Use the extension cable 11 and the plug-in adapter cable 12 to connect to the 12 V supply voltage and an external video/DVD device: Red wire = +12V Ignition Black wire = Ground Red RCA plug = Audio In (R) White RCA plug = Audio In (L) Yellow RCA plug = Video In Blue phono plug = IR pass through for Blaupunkt DVD players (DVD-ME2, DVD-ME3 & DVDME R). Interior Lighting Connection System Cable 9 OPERATION Controlling the interior lighting (monitor) There are two switches for the lights: ON ON : 2 Opening the monitor English · Push the monitor release latch to flip down the LCD display. 3 3 and interior lighting 4 This button is used to switch the lights on/off. [. . . ] · Put in a new bulb (12 Volts, 3 Watts). · Reinstall the monitor. A 21 B Metal cover Bulb 13 SPECIFICATIONS Model TFT-LCD Size Aspect Ratio Open to Close Dome Light Screen Size Pixel Format (WxRGBxH, pixels) Contrast Ratio Signal System Power Supply Video Input Level Audio Input Level Operating Temp Storage Temp Display Method Viewing Area (WxH, mm) Viewing Angle left-right Viewing Angle top-bottom Brightness Monitor Dimension (WxHxD, mm) Connector Response Time (msec) IVMR-7002P 7. 0" (12. 7 cm) 16:9 0° to 180° Yes 7. 0" (12. 7 cm) 480 x 3 (RGB) x 234 150:1 NTSC 10. 0V. . . 16. 0V Composite Video 0. 7Vpp, 75 Ohm 0-0. 3 Vrms -20° to +70° C -30° to +85° C TFT active matrix LCD 154. 08 x 86. 58 60°/60° 60°/30° 400 cd/m2 166 x 100 x 6. 79 13 pin DIN cable 50 IVMR-1042P 10. 4" (26. 4 cm) 4:3 0° to 180° Yes 10. 4" (26. 5 cm) 640 x 3 (RGB) x 480 200:1 NTSC 10. 0V. . . 16. 0V Composite Video 0. 7Vpp, 75 Ohm 0-0. 3 Vrms 0° to +50° C -20° to +60° C TFT active matrix LCD 211. 2 x 158. 4 40°/40° 20°/25° 250 cd/m2 265. 0 x 188. 8 x 12max 13 pin DIN cable 40 English 14 Robert Bosch Corporation Sales Group - Blaupunkt Division 2800 S. [. . . ]