User manual BLAUPUNKT IVMR-7001

[. . . ] 24 Closing the monitor . . . . . . . . . . . . . . . . . . . . . . . 24 Switching on the monitor . . . . . . . . . . . . . . . 24 Display controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Please check that your device is supplied with all the parts. If one of the listed parts is missing, please contact your dealer immediately. Do not subject the monitor to the wet or moisture. After installing the monitor, avoid knocking it or pulling it downwards excessively, since this will loosen the screws and the monitor could drop off. Standard package Monitor (including mounting fixture) Remote control with battery IR-Headphones 500 cm long, 8-pin system cable (only for AV signal converter) Operating instructions 20 USING FOR THE FIRST TIME Using the interior light There are three settings for the interior light: OFF, DOOR and ON (see diagram below). DOOR: With this setting, the lights only come on when the vehicle's doors are opened. ON: The lights are switched on. OFF DOOR ON Circuit diagram 21 DANSK PORTUGUÊS W = White = Connection to the sensor B = Black = Ground R = Red = Electrical connection ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH DEUTSCH Using for the first time Notes: There is no electrical cable connected to position "B", since "B" is connected to the ground via two screws. The power supply must be 12 volts. USING FOR THE FIRST TIME Changing the light bulb To fit a new bulb, proceed as follows: Wiring Bulb for the main unit Light cable for the main unit Set the light switch to "OFF". Push back the bulb cover and open it (see diagram below). Remove the old bulb and dispose of it. Connecting cable Fit a new bulb. Close the bulb cover. Bulb cover Screws Red = Electrical supply (12 V) White = Internal lighting system Black = Ground Caution: The screws have different sizes. Make sure that you insert the screws in the correct positions. Make sure that the screws are screwed tight to ensure a good ground connection. Light bulb Light bulb specifications Diameter: Length: Voltage: Type: 8 mm 29 mm 12 V direct current, 5W Stanley A3022C or a type with the same specifications Monitor connection Connecting cable System cable Light cable for the main unit 22 USING FOR THE FIRST TIME Select a suitable position for secure installation of the monitor: The device must not distract the driver or restrict the driver's view. The ability to enter and get out of the vehicle must not be impeded. The device must not be installed in such a way that could prevent the other vehicle components from functioning properly (e. g. Make sure that the device is installed in a safe and secure position and cannot become detached in the event of an emergency stop. Do not attach the device merely to the roof liner. If you need to drill additional holes, make sure you do not drill through the vehicle's sheet metal. Avoid using the monitor over a longer period of time whilst the engine is off so as to prevent the battery from becoming drained. DEUTSCH Installing the monitor 23 DANSK PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH OPERATION Operation Opening the monitor Press the monitor release button to flip down the LCD display. Closing the monitor Rotate the monitor back to its central viewing position (see the following diagram). To watch the television, lower the monitor until it is at an angle of 90 degrees to the main unit. Push the monitor back into its main unit so that the screen clips back into the releasing/locking mechanism. Switching on the monitor Repositioning the monitor The monitor can be rotated by up to 30 degrees to the right and left from its central viewing position (see the following diagram). Press the power-on button on the main unit or on the remote control to switch the monitor on/off. Note: Before the monitor is switched on, the power indicator lights up orange. This means that the monitor is connected to the 12 V direct current electrical supply. Furthermore, "NO SIGNAL" will flash on and off in the on-screen display (OSD) as long as there is no A/V input signal present. 24 OPERATION DEUTSCH Display controls Remote control AV/TV MUTE POWER MENU CHANNEL VOLUME Press this button to switch between AV and TV channels. [. . . ] Adjust your preferred volume using the volume control on the left whilst making sure you do not obstruct the sensors. 2. Move the on/off switch on the headphones to the on position. 28 OFF / ON IR-HEADPHONES 4. For stereo audio, move the switch to the stereo position. Move the switch to the mono position for mono audio/video devices. [. . . ]