User manual BLAUPUNKT IVMS-7001

[. . . ] 14 Mark out the dimensions . . . . . . . . . . . . . . . . 15 Carefully cut open the headrest cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Open the headrest and remove filling and other items . . . . . . . . . . . . . . . . . . . . . [. . . ] Note: Take appropriate action to ensure that the headrest is not damaged while fitting the monitor. Accessories supplied Connecting cable Extraction tool Operating instructions 14 FITTING/REMOVAL DEUTSCH Mark out the dimensions Feel the covering of the headrest carefully to ensure that there are no invisible parts that would prevent the monitor from being fitted. Use the cardboard template provided to mark out the area that will need to be cut. Carefully cut open the headrest cover Use a knife with an adjustable cutting depth to cut out the planned area. Make the first cut inside the marked area at a point about 0. 5 cm from one of the corners, then make a diagonal cut to a point about 0. 5 cm from the opposite corner. Make a similar cut between the other two diagonally opposed corners. away from the cut area. Adjust the cutting depth of the knife to about 2. 5 cm, and cut into the headrest following a line about 0. 5 cm inside the marked edge. Carefully lift the filling material at one corner, and cut deeper into the material with the knife. Remove the filling material in small pieces. As you do this, lift one piece of the filling material, and ensure that the cut is being made to an even depth. To remove other pieces, use a Dremel saw or another suitable tool. 15 DANSK PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO Open the headrest and remove filling and other items Carefully lift the covering material FRANÇAIS ENGLISH FITTING/REMOVAL Insert the monitor to check that it will fit into the cut area, and make adjustments if necessary. Insert the mounting frame in the headrest Before connecting the monitor, pass the connecting cables through the holes provided in the mounting plate, as shown in the illustration. Insert the mounting plate into the area that has been cut out, and fix it in place with appropriate fastenings. Lay the cable through the headrest Now pass the supplied cables through the opening so that they emerge from the underneath of the headrest. If possible, cover the cable with a cable tunnel. Now connect the power supply, ground and video signal cables, to check that the monitor is working. Inserting the monitor Before connecting the monitor, pass the connecting cables through the holes provided in the mounting plate, as shown in the illustration. Insert the monitor into the mounting plate, and attach it with appropriate fastenings. Monitor Mounting plate 16 FITTING/REMOVAL To remove the screen, insert the extraction tool between the screen and the mounting plate. Insert the extraction tool at the place where a slot has been provided between the screen and the mounting plate. DEUTSCH DANSK PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH Check and adjust the monitor then apply the Velcro strips Connect the monitor, place it temporarily in the cut-out, and place the headrest into position. [. . . ] If you wish to enforce a claim under the manufacturer's guarantee that is provided by Blaupunkt, please send the faulty equipment together with the purchase receipt to the Blaupunkt customer service centre in your country. You can find out which address is closest to you by contacting the telephone hotline listed on the back page of this booklet. Blaupunkt retains the right to rectify defects or supply a replacement. Visible screen area: 155. 52 (W) x 87. 75 (H) mm Angle of view: 5. 6": 7": from left and right: 45°, from above: 10°, from below: 30° from left and right: 60°, from above: 60°, from below: 30° Full monitor dimensions: 5. 6": 140 (W) x 114 (H) x 42 (D) mm 7": 200 (W) x 127 (H) x 33, 5 (D) mm Monitor weight: < 500 g Subject to changes! [. . . ]