User manual BLAUPUNKT KIEL CD35

[. . . ] Radio / CD Kiel CD35 Malaga CD35 7 645 050 510 7 645 060 510 Operating instructions http://www. blaupunkt. com 2 1 3 4 5 6 11 10 9 8 7 2 CONTROLS 1 Button to switch the device on/ off and operate the volume mute function. button SRC Short press: Switch sources between CD, CD changer (if connected) and AUX. Long press: Briefly display the clock time. Volume control CD compartment TRAF RDS button Short press: Switch traffic-information standby on/off. [. . . ] "OFF" or "ON" is displayed alongside "REG". press the SRC button 2 repeatedly until the memory bank (e. g. "FM1") appears in the display. To switch REGIONAL on/off, press the or button 7. RDS functions The convenient RDS functions AF (Alternative Frequency) and REGIONAL extend your radio's range of functions. AF: If the RDS function is activated, the radio automatically tunes into the best receivable frequency for the station that is currently set. REGIONAL: At certain times, some radio stations divide their programme into regional programmes providing different content. You can use the REG function to prevent the car radio from switching to alternative frequencies that are broadcasting different programme content. Note: REGIONAL must be activated/deactivated separately in the menu. Switching the RDS function on/off If you want to use the RDS functions (AF and REGIONAL), Press the MENU button 8. Selecting the waveband / memory bank This device can receive programmes broadcast over the FM frequency range as well as the MW and LW (AM) wavebands (MW and LW only on the Malaga CD35). There are three memory banks available for the FM waveband (FM1, FM2 and FMT) and one for each of the MW and LW wavebands. Six stations can be stored in each memory bank. The stations are stored in the FMT memory bank. Press the MENU button 8. 31 RADIO MODE Note: Any stations previously stored in this memory bank are deleted in the process. Cancelling SCAN and continuing listening to a station Press the MENU button 8. Scanning stops and the radio continues playing the station that it tuned into last. Press and hold down the BND·TS button ; for longer than two seconds. "FM TSTORE" appears in the display. After the process has completed, the radio will play the station that is stored in memory location 1 of the FMT memory bank. Setting the scanning time Press the MENU button 8. Press the or button 7 repeatedly until "SCAN TIME" appears in the display. Set the desired scanning time usbuttons 7. ing the When you have finished adjusting the setting, Listening to stored stations Select the memory bank or waveband. Press the station button 1 - 6 : that corresponds to the station that you want to listen to. press the MENU button 8 twice. Note: The scanning time that you set is also used when scanning in CD mode and in CD-changer mode. Scanning receivable stations (SCAN) You can use the scan function to listen to all the receivable stations briefly. You can set the scanning time in the menu to between 5 and 30 seconds (in steps of 5 seconds). Starting SCAN Programme type (PTY) Besides transmitting the station name, some FM stations also provide information on the type of programme they are broadcasting. Your car radio can receive and display this information. For example, the programme types can be: CULTURE TRAVEL JAZZ SPORT NEWS POP ROCK CLASSICS You can use the PTY function to select stations of a particular programme type. Press and hold down the MENU button 8 for longer than two seconds. "SCAN" appears briefly in the display followed by a flashing display of the current station name or frequency. 32 RADIO MODE PTY-EON If you specify the programme type and start seek tuning, the radio will switch from the current station to a station of the selected programme type. Note: If the tuner does not find a station that matches the selected programme type, you will hear a beep and "NO PTY" appears briefly in the display. [. . . ] Adjusting the X-BASS boost LEVEL DISPLAY DEUTSCH DANSK PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH Configuring the level display The level display temporarily provides you with a symbolic representation of the volume and audio settings whilst you are adjusting them. When you are not changing any settings, the level display depicts the peak music/speech output. You can switch the level display on/off. Press the MENU button 8. "MENU" appears in the display. Press the AUDIO button 9. "BASS" appears in the display. Press the Press the button 7 repeatedly until "XBASS" appears in the display together with the current setting. or button 7 repeatedly until "PEAK LVL" appears in the display. Press the Press the or button 7 repeatedly until the setting that you want appears in the display. When you have finished adjusting the setting, or button 7 to switch between "PEAK ON" and "PEAK OFF". [. . . ]