User manual BLAUPUNKT KIEL CD36

[. . . ] Radio CD Kiel CD36 Malaga CD36 7 646 050 510 7 646 065 510 Operating instructions http://www. blaupunkt. com 2 1 3 4 5 6 11 10 9 8 7 2 CONTROLS DEUTSCH 1 2 Button to switch the device on/ off and operate the volume mute function. SRC button Short press: Switch sources between CD, CD changer (if connected) and AUX. Long press: Briefly display the clock time. Volume control CD compartment TRAF RDS button Short press: Switch traffic-information standby on/off. [. . . ] The car sound system starts with the last setting activated (radio, CD, CD changer or AUX). RDS functions The convenient RDS functions AF (Alternative Frequency) and REGIONAL extend your radio's range of functions. G AF: If the RDS function is activated, the radio automatically tunes into the best receivable frequency for the station that is currently set. G REGIONAL: At certain times, some radio stations divide their programme into regional programmes providing different content. You can use the REG function to prevent the car radio from switching to alternative frequencies that are broadcasting different programme content. G Note: REGIONAL must be activated/deactivated separately in the menu. Switching the RDS function on/off If you want to use the RDS functions (AF and REGIONAL), press and hold down the TRAF RDS button 6 for longer than two seconds. The RDS function is active when an RDS symbol lights up in the display. "SENS LO1" means it is set to the lowest sensitivity setting. Set the desired sensitivity using the buttons 7. When you have finished adjusting the setting, press the MENU button 8. Note: G You can set different sensitivity levels for FM and MW or LW (AM) (MW/LW only on the Malaga CD36). DEUTSCH DANSK PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH Press the Note: G Any stations previously stored in this memory bank are deleted in the process. Press and hold down the BND·TS button ; for longer than two seconds. "FM TSTORE" appears in the display. After the process has completed, the radio will play the station that is stored in memory location 1 of the FMT memory bank. Listening to stored stations Select the memory bank or waveband. Press the station button 1 - 6 : that corresponds to the station that you want to listen to. Storing stations Storing stations manually Select the memory bank that you want (FM1, FM2, FMT) or one of the wavebands (MW or LW) (MW/ LW only on the Malaga CD36). Press and hold down one of the station buttons 1 - 6 : for longer than two seconds to assign the station to that button. Scanning receivable stations (SCAN) You can use the scan function to listen to all the receivable stations briefly. You can set the scanning time in the menu to between 5 and 30 seconds (in steps of 5 seconds). Starting SCAN Press and hold down the MENU Storing stations automatically (Travelstore) You can automatically store the six stations providing the best reception in the region (only FM). The stations are stored in the FMT memory bank. button 8 for longer than two seconds. "SCAN" appears briefly in the display followed by a flashing display of the current station name or frequency. 33 RADIO MODE Cancelling SCAN and continuing listening to a station PTY-EON If you specify the programme type and start seek tuning, the radio will switch from the current station to a station of the selected programme type. Note: G If the tuner does not find a station that matches the selected programme type, you will hear a beep and "NO PTY" appears briefly in the display. The radio will then retune to the station that it received last. G If the tuned radio station or another station on the broadcasting network broadcasts your selected programme type at a later point in time, the radio will automatically switch from the currently tuned station or from CD mode or CDchanger mode to the station whose programme type matches the one you selected. G If you do not want this PTY EON switching, disable it in the menu with "PTY OFF". First, press one of the SRC 2 or BND·TS buttons ;. [. . . ] Adjusting the X-BASS boost LEVEL DISPLAY Configuring the level display The level display temporarily provides you with a symbolic representation of the volume and audio settings whilst you are adjusting them. When you are not changing any settings, the level display depicts the peak music/speech output. You can switch the level display on/off. Press the MENU button 8. "MENU" appears in the display. Press the AUDIO button 9. "BASS" appears in the display. Press the Press the Press the button 7 repeatedly until "XBASS" appears in the display together with the current setting. or button 7 repeatedly until "PEAK LVL" appears in the display. or button 7 repeatedly until the setting that you want appears in the display. When you have finished adjusting the setting, Press the or button 7 to switch between "PEAK ON" and "PEAK OFF". [. . . ]