User manual BLAUPUNKT MADISON DJ31

[. . . ] Radio / Cassette Boston C31 Dresden C31 Dublin C31 Cleveland DJ31 Madison DJ31 Operating instructions 1 2 17 16 3 15 4 5 6 14 7 8 13 12 10 11 9 3 SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH DEUTSCH PORTUGUÊS ESPAÑOL OPERATING ELEMENTS 2 : ; < = > ? DEUTSCH PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH 1 3 4 5 6 7 8 Button, to unlock the removable control panel (release panel) BAND button (Band), to switch to radio mode, to select the FM memory levels and the MW and LW frequency ranges (MW and LW are not available on the Dresden C31 and Cleveland DJ31) TS, to start the Travelstore function FMT button (Dresden C31 and Cleveland DJ31), to select the FM memory levels, to switch to radio mode, to start the Travelstore function. RDS button, to switch the RDS function on/off (Radio Data System). SCAN button, to start the scan function. Cassette eject Cassette compartment button, fast winding button, fast winding 9 @ A X-BASS button, to activate the X-Bass function. [. . . ] The car audio system will be muted to the mute level selected. press the MENU button = twice. 30 ADJUSTING THE VOLUME DEUTSCH Configuring the confirmation beep For some functions you will hear a confirmation beep if you keep a button pressed for longer than two seconds. For instance, after storing a radio station to a station button you will hear a confirmation beep. You can configure the beep. < until "BEEP OFF" or "BEEP ON" appears in the display. "BEEP OFF" means that the confirmation beep is switched off, "BEEP ON" means that it is switched on. 31 PORTUGUÊS ESPAÑOL SVENSKA press the MENU button =. NEDERLANDS Make your selection using the or button <. When you have finished making your changes, ITALIANO FRANÇAIS Press the MENU button =. Keep pressing the or button ENGLISH RADIO MODE Radio mode This unit is equipped with an RDS radio receiver. Many of the receivable FM stations transmit a signal that not only carries the programme but also additional information such as the station name and programme type (PTY). The station name appears in the display as soon as it is received. Switching REG on/off Press the MENU button =. Keep pressing the or button < until "REG" appears in the display. "OFF" or "ON" is displayed alongside "REG". To switch REG on/off, press the or button <. Keep pressing the or button < until "SENS HI" or "SENS LO" appears in the display. The display shows the currently set value for sensitivity. "SENS HI6" means that the tuner is highly sensitive. "SENS LO1" means it is set to the lowest sensitivity setting. If "SENS LO" is selected, "lo" lights up in the display. Set the required sensitivity using the and buttons <. When you have finished making your changes, Press the or button <. The unit tunes into the next receivable station. Tuning into stations manually You can also tune into stations manually. Press the q or button <. Note: You can only tune into stations manually if the RDS function is deactivated. Browsing through broadcasting networks (only FM) If a radio station provides several programmes, you have the option of browsing through its so-called "broadcasting network". press the MENU button =. Storing stations Storing stations manually Press the or button < to move to the next station on the broadcasting network. Select the required FM1 / FM2 / FMT memory or one of the MW / LW frequency ranges (only FM in the case of the Dresden C31 and Cleveland DJ31 units). Tune into the required station. Note: q The RDS function must be activated before you can use this feature. 33 RADIO MODE Press one of the station buttons 1 5 > for longer than two seconds to store the station to that button. Starting SCAN Press the SCAN button 4. Scanning begins. "SCAN" briefly appears in the display followed by a flashing display of the current station name or frequency. [. . . ] When you have finished making your changes, or button < to adjust the balance (right/left). When you have finished making your changes, press the AUDIO button ;. Setting the front/back volume distribution (fader) To adjust the front/back volume distribution (fader), press the AUDIO button ;. Adjusting the treble settings To adjust the treble, press the AUDIO button ;. "BASS" appears in the display. press the AUDIO button ;. "BASS" appears in the display. Keep pressing the Press the button < until "TREB" appears in the display. Keep pressing the Press the button < until "FADER" appears in the display. or button < to adjust the treble. [. . . ]